Tom King Posted January 13, 2014 Report Posted January 13, 2014 http://www.hardwoodlumberandmore.com/Articles/ArticleViewPage/tabid/75/ArticleId/18/Workbench-Finish.aspx Quote
Eric. Posted January 13, 2014 Report Posted January 13, 2014 The author seems a bit confused, as these two "requirements" contradict each other: -will allow you to easily slide work across the surface with little resistance -will offer enough resistance to stop items before they slide off the bench and hit the floor I have to pretty much disagree with the first part...it's not a saloon bar top in an old western movie...who needs to "slide" work across the surface of their bench? A slick bench top only makes work more difficult. Also he recommends a "durable" finish, then goes on to suggest BLO and wax...a less durable finish I cannot fathom. I personally think finishing a bench is relatively unimportant except for the glue factor...for that alone it's worth it. But any old finish will do for that. There's not a finish that exists that can truly "protect" a bench from the beating it's going to take. IMO a few coats of BLO, and a refresher coat every six months or so is perfectly adequate...just to keep the wood from drying out and wanting to check. Quote
Dan S Posted January 13, 2014 Report Posted January 13, 2014 I have to agree with Eric.The two finishes I have seen used most often on a bench are:1. BLO (sometimes topped with wax)2. Danish oil (sometimes topped with wax) Quote
Freddie Posted January 13, 2014 Report Posted January 13, 2014 Is it ok to subsitute the blo for butcher block oil, in terms that the bbo is clear and the blo is more yellow. I just happen to have both on me and i love the clear results of the bbo but am not sure of the cons one might encounter. Quote
G S Haydon Posted January 13, 2014 Report Posted January 13, 2014 It's ok not to apply finish to your bench 2 Quote
Dan S Posted January 13, 2014 Report Posted January 13, 2014 Is it ok to subsitute the blo for butcher block oil, in terms that the bbo is clear and the blo is more yellow. I just happen to have both on me and i love the clear results of the bbo but am not sure of the cons one might encounter.Butcher block oil is "usually" just mineral oil. The only down side to it, is it never really dries, and could potentially transfer to a work piece if the benchtop is saturated. 1 Quote
ChetlovesMer Posted January 13, 2014 Report Posted January 13, 2014 I think people put entirely too much thought into what finish to put on their bench. Here's the answer to what is the best finish for your bench-top... Wait for it. ... IT DOESN'T MATTER. In my humble opinion, put what ever you like on your bench. I used 3 simple coats wipe on varnish everywhere except the top. The top got a thin coat of oil. Having said that, I really think I could have put anything on the top and it would have been fine. My bench-top has been worked on, scratched, nicked, biffed, bashed, and everything else. Unless you are putting a high-gloss bowling alley finish and two layers of wax on it, eventually it gets worn to the point where it's about the same as everyone else's. I know very good woodworkers who've put poly on their bench top, I know guys who have oil, I know guys who go with it rough tough and in the buff. Seriously, it doesn't matter. Put what you like on it. I went to a workbench building seminar late last year. As soon as the subject of what finish should be on the bench-top came up, It brought the whole seminar to a halt! It was like bringing up pass-interference at an NFL referee meeting. People argued tooth and nail over which finish you should use. We'd still be arguing about this if the seminar moderator wasn't smart enough to say "Let's move on." Seriously, I'm a firm believer put what ever you like on there, or leave it naked. I promise it is very unlikely that the chest of drawers you are about to build will be in any way affected by which finish you chose to put on your bench. Quote
Tpt life Posted January 13, 2014 Report Posted January 13, 2014 I think the article just contains some poor articulation. There is a balance to be struck between frictionless and super sticky. Each have their merits but should not be pursued exclusively. Waxed BLO should not need to be renewed as often as unwaxed. Also, they will not chip or peel over time and fresh wax is cheap and easy requiring no sanding etc. I think some of us read "durable" and "protection" in different ways. I cannot say after reading the article that I could definitively say the author disagrees with you Eric but I think it was articulated differently. Quote
G S Haydon Posted January 13, 2014 Report Posted January 13, 2014 Chet "rough tough and in the buff" had me laughing :-). Quote
ChetlovesMer Posted January 13, 2014 Report Posted January 13, 2014 Thanks, Graham. I strive to please. 1 Quote
CStanford Posted January 13, 2014 Report Posted January 13, 2014 http://www.hardwoodlumberandmore.com/Articles/ArticleViewPage/tabid/75/ArticleId/18/Workbench-Finish.aspx The great Alan Peters kept his benchtop waxed. Quote
G S Haydon Posted January 13, 2014 Report Posted January 13, 2014 A welcome reminder of a wonderful craftsman, Quote
wtnhighlander Posted January 14, 2014 Report Posted January 14, 2014 The coating I prefer on my bench is sawdust. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.