Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Super basic wiring question….please help

Featured Replies

Let me preface my inquiry with the fact that i know very little about electrical and wiring.  this is going to sound like a dumb question to most of you, but bear with me.  I bought a new T5 fluorescent light fixture for my shop.  i want to wire it to a 3 prong plug so i can plug it into a wall outlet.  the light fixture has 3 wires…black, white, and green.  my cord wire has the same 3 colors.  my question is, do i connect the green ground wires together or do i use the green screw that is mounted in the metal body of the fixture?

Connect green wires together, and also connect green wires to the grounding screw.  On the plug, white to silver screw, and black to brass.

Not a stupid question at all --- proper grounding is important and sometimes throws folks. Tom's answer is spot-on.

I used to work with my brother in law who ran a construction business. I learned electricity the Pittsburgh way. Black and gold :) green and green and white goes to silver

  • Author

Thanks guys! One more question though. If I connect the two green wires together with a wire nut how can I connect them to the grounding screw on the fixture as well?

Since nobody mentioned it, be sure to turn the breaker off Nick  ;)

 

Sometimes it's easy to focus on the issue at hand an miss the thing that will bit you.

==>Sometimes it's easy to focus on the issue at hand an miss the thing that will bit you.

Yea, target focus will bite you every time... :)

 

==>be sure to turn the breaker off Nick

I have as yet to do that one...

 

But, reminds me of a funny story. On a service upgrade, I did the donkey work and hired an electrician pull the permit, deal with the utility, support inspections, etc.

 

In the middle of the job, went to see how it was going... In prep for inspection, he was labeling the breakers. Was appalled to discover that, instead spending time determining which breaker to pull, he simply went around grounded hots... He looked at the expression on my face, smiled and said, "Well, we're testing the breakers at the same time"... :)

 

Takes all kinds... I subsequently learned that the practice is more prevalent than I suspected...

Before GFCI's, it didn't matter which of the white and black wires went on which lug in a plug.  I had some type SO extension cords that I made up in the early '70s-still in use actually, although the "plugs" have been replaced at least once.

 

The wire is kind of thick, and I had hooked the wires up to the male and female ends just like they came out of the cover.  In other words, on one end of the cord white was to silver, and on the other end black was to silver.  It worked fine for several years until the inspector made us start using GFCI's on a temporary pole.

 

With the first temporary service I was using with a GFCI breaker, at first I had both cords hooked together, and everything ran fine.  Then, for whatever reason, I was using one cord, and nothing would run.  Plugged another cord into the first one, and it went back to work. 

 

It took me a little while to sit there and figure this puzzle out.  Changing the neutral and hot wires on one end of each cord put us back in business. 

 

When we're pulling wires for anything, I write on the cover of the wire at the box what it is.  A service panel comes with stickers, or a paper panel on the cover.  I leave the cover sitting near the box, and when I hook a wire up to a breaker, we write the name for that circuit in the cover.  Otherwise, any kind of way you check a circuit, something has to be plugged into that circuit on the other end.

  • Author

Thanks for all the advice. I just finished the wiring and install. The amount of light produced by this fixture is mind boggling! I love it

==>When we're pulling wires for anything, I write on the cover of the wire at the box what it is.  A service panel comes with stickers, or a paper panel on the cover.  I leave the cover sitting near the box, and when I hook a wire up to a breaker, we write the name for that circuit in the cover.  

Yup, someone doing it the proper way... Last electric job, we just used walkies-talkies... Worked, but labeling would certainly be a better approach...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Who's Online (See full list)

  • There are no registered users currently online

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.