Recommended Posts

Posted

Looking some opinions here guys. Trying to decide on a bandsaw. I've been looking at the grizzly deluxe. I saw a post on here earlier about someone recently purchasing one and can't find it. I've seen people saying the 1hp isn't enough but thinking it might be for me. I'm sure this will be a very opinionated post but here we go. Lol

Sent from my iPhone using Tapatalk

Posted

I had a Grizzly G0555 bandsaw with 1HP and it did just fine. I made several bandsaw boxes with it and also occasionally resawed up to 6" stock. As long as you don't try and rush cuts through thicker material it will do the job. 

Posted

+1 on everything estesbubba said.  I have the G0555P which is the same setup, just a different color, and have had similar experiences as him. I will add that having a good quality blade on the saw makes a real difference in how the saw performs.  A cheep blade can make the saw seem like it needs more HP where a good blade can make it cut like a hot knife through butter.   I use a Timberwolf 1/4", 6TPI blade on my saw.  For a 14" bandsaw with a 6" resaw, I do not think a 1HP motor is a real limitation, speaking from experience. 

 

However, to better answer your question, what do you intend on using the bandsaw for?  As a comparision, I do a little bit of everything with it.  Lots of curves, lost of straight lines, the occasional bowl blank and the less occasional resaw.  Most of my cuts are with 3/4"-2" thick material, though have gone much thicker without issue. 

Posted

I just bought the Laguna 14-12 and am loving it.  Check it out.  Yesterday I ripped and resawed 1 1/2" white oak effortlessly.  Plus, the ceramic guides are the bomb.  I looked at Grizzley too.

 

miw!

Posted

I also have a G0555P. I do not have a decent blade, however. But here's my experience: we've had it for 3+ years, never a good blade on it, and use it a decent amount, cutting through 1.5" thick hardwoods (mahogany, oak, ash, some maple and poplar). It seems to do well. We did have to replace the guide bearings (bushings?) recently, but we were able to find them for cheap.

Here's what I don't like about it:

the manual is lacking, but they do have some decent videos.

The fence is nothing fancy, and the thing the fence attaches to (don't know the technical name) is poorly designed, as it is not at the same level as the "table". But. I rarely use the fence, as I don't do any resawing, so generay it's not attached.

As far as horse power goes, like those above said, I think the difference is in the blade. We use cheap, but aggressive blades, and they go through most anything.

Posted

I have the same Grizzly bandsaw as the others here. I have never had any trouble with it. I have the 6" riser for resawing and it works great. I usually use the Olson blades from woodcraft. Cheap and get the job done. I recently purchased a Laguna 1/4" blade and I love it. It's fairly aggressive which is nice for what I do.

Posted

I made a table and fence for mine and also got rid of the screaming bearing guides. I made my own guides out of hardwood, soaked in mineral oil, then buried the blade and teeth into them. 

 

post-8178-0-04548000-1398774142_thumb.jppost-8178-0-60705400-1398774142_thumb.jppost-8178-0-12809600-1398774143_thumb.jppost-8178-0-63448200-1398774143_thumb.jppost-8178-0-13731200-1398774144_thumb.jppost-8178-0-63225400-1398774144_thumb.jppost-8178-0-14696200-1398774145_thumb.jppost-8178-0-60987200-1398774145_thumb.jp

 

 

  • Like 1
Posted

Dnorris, I definitely would buy this saw again. I got mine w/ the riser block and the resaw fence. If you decide to get the Griz, just have a Timber Wolf or better blade ready and don't even take Grizzly's stock blade out of the box. Scrap it immediately!

Posted

Probably, because it's a good saw and a great price. I wasn't involved in the decision to buy that particular saw. If I was, it probably would have taken 10 times as long as I analyzed every possibility.

Posted

I have the G0555LANV, which is the black anniversary edition - essentially the same machine. I have been more than pleased with its performance. The limitation is the guy who uses it

Posted

I have the G0555LANV, which is the black anniversary edition - essentially the same machine. I have been more than pleased with its performance. The limitation is the guy who uses it

Can't comment on how well it performs; mine gets here tomorrow.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Who's Online   3 Members, 0 Anonymous, 59 Guests (See full list)

  • Forum Statistics

    32.1k
    Total Topics
    437.6k
    Total Posts
  • Member Statistics

    26,009
    Total Members
    3,644
    Most Online
    Joseph b
    Newest Member
    Joseph b
    Joined