Recommended Posts

Posted

I recently had some questions about  my table saw, but I came here and everything was throughly explained.   The blade that came with my Ryobi table saw is a 10" general purpose blade with 5/8" arbor, 36 teeth and a maximum operating speed of 5,500 RPM. Part of the problem I  had may have been caused because I used that blade to do a great deal of ripping, and I've since read that ripping blades generally have more teeth. 

 

I don't want to have any more problems, so I'm going to buy more blades. One will duplicate what the saw came with, because I think Ryobi should know what kind of blade to use for general purposes, but I am also going to buy a blade for ripping.

 

I'm looking for advice. What kind of blades do you think I should buy?

Posted

Ripping blades generally have fewer rather than more teeth and deeper gullets. Dedicated crosscuts are 60-80 teeth often times. I lack the experience with your particular blade but your problem is likely not tooth count.

  • Like 2
Posted

I'm guessing that your table saw is 1.5 HP or less.  I'm also guessing that you are starting out as a hobbyist, and won't be using your blades 40 hours a week.

 

Here's what I use and like:

Ripping: Freud D1024X Diablo 10-Inch 24-Tooth ATB Ripping Saw Blade with 5/8-Inch Arbor and PermaShield Coating

Cross Cutting: Freud D1080X Diablo 10-Inch 80-tooth ATB Finish Saw Blade with 5/8-Inch Arbor and PermaShield Coating

General Purpose: Freud D1040X Diablo 10-Inch 40-Tooth ATB General Purpose Saw Blade with 5/8-Inch Arbor and PermaShield Coating...

 

These are good quality inexpensive blades that give a clean cut.  They are thin kerf (they turn less wood into sawdust) which is better for saws with less than 2 HP.  They can't be re-sharpened as many times as more expensive blades, but I think they are a good choice for a hobbyist.

 

If it were me I'd start by getting the rip blade and the general purpose.  I'd keep the general purpose on the saw except when I was doing a lot of ripping, or ripping especially thick or hard wood.  If I wanted better quality cross cuts, or was doing a lot of cross cuts, then I'd get a dedicated cross cut blade.

 

If you use the links above, or the Amazon links on this site, then Amazon will help support this site.  You won't pay any extra.

 

By the way, plywood always counts a "cross cut", regardless of the orientation.

Posted

You might be surprised to hear just how poor of a blade most companies will choose to put on their saws, including most of the Ryobi saws.  Once upon a time, the Ryobi BT3000/3100 came with a very good stock 36T blade made by Freud in Italy....other than that, most Ryobi blades are really mediocre at best.  To be assured of decent basic quality, I'd stick with brands like Infinity, Forrest, CMT, Freud, Irwin Marples, Guhdo, Tenryu, Ridge Carbide, DeWalt's Precision Trim series, Leitz, Oshlun, Amana Tool, and Systimatic.  For woodworking, I'd avoid DW's construction series, HF, most Sears, Vermont American, Oldham contractor series, Avanti/Avanti Pro, Irwin Marathon and Classic, Work Force, most Ryobi, and other off names.

 

Ripping generally requires fewer teeth, not more.   A decent 24T thin kerf ripper like the aforementioned Freud Diablo D1024X or Irwin Marples are solid choice for a pure bulk ripper.  

 

(some homework for you)...

The ABCs of Picking Saw Blades

 

Current Saw Blade Bargains

Posted

Just what I needed, thanks. I couldn't answer each contributor separately, so I'll  write my comments here.

 

(1) C. Shaffer: My problem was that the Circuit breaker tripped twice while I was using my table saw. After reviewing the answers I received, I figured that the problem might have been caused by a dull blade, or prolonged continuous usage, or forcing the stock into the blade. I decided to be more patient in the future and to buy a new blade.

(2) Beechwood Chip: Well, I've never used it for 40 hours in any one week, but it is 15 amps. That roughly converts to about 2.2 HP. As to your suggested blades, it's interesting that I had decided upon the  Freud D1024X Diablo 10-Inch 24-Tooth ATB Ripping Saw Blade with 5/8-Inch Arbor and PermaShield Coating before I saw your posting. I had gone to Amazon for more information after posting my question, and I was impressed by its reviews. There are always some naysayers, but  most people love it. I agree with your two-blade suggestion. I had decided upon the same thing.

 

(3) knotscott: As a veteran reviewer of Amazon reviews, I know that no product is ever unanimously loved, but why take a chance; I'm going to replace my general purpose blade by one made by another manufacturer.

 

Thanks, all.

Posted

My problem was that the Circuit breaker tripped twice while I was using my table saw. 

In addition to what's been mentioned, it could be a dull blade or dirty blade (not likely if you've only used it a few times), a blade alignment problem, or trying to cut too fast, too thick, or too hard.  

 

Do you see any burn marks on the wood?

Posted

It can also be handy to have a 7-1/4" circular saw blade for table saw use.  They are thinner kerf than a thin kerf 10" blade so they really zip right through stuff on a table saw.  You're just limited to about 1.5-1.75" of cutting depth, which is enough for the vast majority of cuts.  Cheaper than a 10" rip blade too.

Posted

Are you running with an extension cord? An undersized or damaged cord can restrict power to the saw and cause cutting problems. Sent from my T-Mobile G2 using Tapatalk 2

Yes, I use an extension cord, but now that you mention it, I'll see if I can do without it.

Posted

It can also be handy to have a 7-1/4" circular saw blade for table saw use.  They are thinner kerf than a thin kerf 10" blade so they really zip right through stuff on a table saw.  You're just limited to about 1.5-1.75" of cutting depth, which is enough for the vast majority of cuts.  Cheaper than a 10" rip blade too.

I have two 7'1/4" circular saws, but I only use them when I have to. I'm just not comfortable with them. The truth is, they frighten me a little.  They're too powerful and too noisy. I much prefer my 5-1/2" trim saw, particularly for plywood but, being battery operated, it doesn't run very long. [if I had known then what I know now....]

 

Oh, I  see now that you're  not saying to use a circular saw; you're saying to use a 7-1/2" blade on my table saw. That thought occurred to me, but I didn't see what use it would be, and I wasn't sure it could be done. You've now straightened me out on this matter. I'll have to give it serious thought. I could just take one from one of my circular saws. Thanks for the idea.

Posted

In addition to what's been mentioned, it could be a dull blade or dirty blade (not likely if you've only used it a few times), a blade alignment problem, or trying to cut too fast, too thick, or too hard.  

 

Do you see any burn marks on the wood?

That's  strange; I did mention dullness and pushing too hard, but only later (...might have been caused by a dull blade, or prolonged continuous usage, or forcing the stock into the blade...). I guess I inadvertently deleted them in the beginning when I was correcting typos or rewording. I do that all the time. No, I didn't see any burn marks.

Posted

It can also be handy to have a 7-1/4" circular saw blade for table saw use.  They are thinner kerf than a thin kerf 10" blade so they really zip right through stuff on a table saw.  You're just limited to about 1.5-1.75" of cutting depth, which is enough for the vast majority of cuts.  Cheaper than a 10" rip blade too.

 

One of the biggest downsides to using 7-1/4" blades is that they're often thinner than the splitter or riving knife on the saw, meaning those safety features can't be used.  

Posted

That's  strange; I did mention dullness and pushing too hard, but only later (...might have been caused by a dull blade, or prolonged continuous usage, or forcing the stock into the blade...). I guess I inadvertently deleted them in the beginning when I was correcting typos or rewording. I do that all the time. No, I didn't see any burn marks.

I think you'd see burning if there was an alignment problem.  I didn't check carefully back through the thread - I just mentioned stuff that I didn't remember seeing in the previous response.

Posted

15 amps isn't a true 2.2 hp my 1 1/2 hp UniSaw isn't happy unless it's on a 20 amp breaker. If you have to use an extension cord get the shortest one that will work and the heaviest wire gauge available. 12/3 is what I use for 120v tools.

  • Like 1
Posted

Motor efficiency must bw accounted for when calculating HP from volts x amps. To achieve 2 HP, a 120 volt, 15 amp motor has to be between 85 and 90% efficient. Typical single phase electric motors are close to 65% efficient, giving a 1.5 or so HP result.

True horsepower is a measue of the actual work the motor can do, so to really measure it you have to measue force x time. No easy way to do that in the shop. That's why the mfg can get away with pretty extravagant HP claims at times.

  • Like 1
Posted

As implied above, if you run a 15 amp tool on a 15 amp circuit, there's a good chance it's going to trip occasionally ( or perhaps often ).  At one time,

I tried running my 15 amp miter saw on a 15 amp circuit and had nothing but problems.  It would trip the breaker occasionally when I first squeezed the trigger, which is when you get the initial high startup current to the motor.  If you are connected to a 15 amp circuit, you might want to think about increasing that to a 20 amp circuit.

Posted

15 amps isn't a true 2.2 hp my 1 1/2 hp UniSaw isn't happy unless it's on a 20 amp breaker. If you have to use an extension cord get the shortest one that will work and the heaviest wire gauge available. 12/3 is what I use for 120v tools.

I couldn't read the specifications in my breaker box because of the light and position, so I took a picture. In the box labeled "MAIN RATINGS" I see the following:

120-240V  A-C 3-wire

125 amperes

There's a lot more, but I guess this is what I want. Anyway, it looks like it's 125 amps. Oh, maybe it's 25 amps, not 125 amps. [You can tell what a great electrician I am]

Posted

As implied above, if you run a 15 amp tool on a 15 amp circuit, there's a good chance it's going to trip occasionally ( or perhaps often ).  At one time,

I tried running my 15 amp miter saw on a 15 amp circuit and had nothing but problems.  It would trip the breaker occasionally when I first squeezed the trigger, which is when you get the initial high startup current to the motor.  If you are connected to a 15 amp circuit, you might want to think about increasing that to a 20 amp circuit.

I find this to be reassuring. To me, a tripped breaker is serious business, and I was going to call an electrician until I learned more from this site. I now think it's a matter of concern but not necessarily cause for panicking. "It happens" is what I get from this board.

Posted

I couldn't read the specifications in my breaker box because of the light and position, so I took a picture. In the box labeled "MAIN RATINGS" I see the following:

120-240V  A-C 3-wire

125 amperes

There's a lot more, but I guess this is what I want. Anyway, it looks like it's 125 amps. Oh, maybe it's 25 amps, not 125 amps. [You can tell what a great electrician I am]

 

The entire panel is rated for 125 Amps.  You need to find the rating for the circuit breaker that tripped.  If it's 15 Amps, consider having an electrician install some 20  Amp circuits with outlets for your power tools.

 

Popping a circuit breaker is no cause to panic, but it shouldn't be a regular thing.  It does mean that you went over the rated safety limit for the wiring.  You should figure out what's causing it to trip, and stop doing that.

Posted

I couldn't read the specifications in my breaker box because of the light and position, so I took a picture. In the box labeled "MAIN RATINGS" I see the following:

120-240V  A-C 3-wire

125 amperes

There's a lot more, but I guess this is what I want. Anyway, it looks like it's 125 amps. Oh, maybe it's 25 amps, not 125 amps. [You can tell what a great electrician I am]

The 125 amps is the rating for the entire panel.  On the individual circuit breaker switches, you should see a number which is the rating for that particular circuit breaker in amps.  So whichever one trips look at that switch and read the number off it.  (Now to be honest I don't really know whether all circuit breakers are labeled like that, but mine certainly are.)

Posted

The 125 amps is the rating for the entire panel.  On the individual circuit breaker switches, you should see a number which is the rating for that particular circuit breaker in amps.  So whichever one trips look at that switch and read the number off it.  (Now to be honest I don't really know whether all circuit breakers are labeled like that, but mine certainly are.)

Thanks for the tip. I'll look again. I'm also going to take a better picture of the specifications, because I can't read them off the aged paper they're printed on, but the photograph comes out fine, I'll just have to be sure to get the entire document in the picture. Oh, and I'll try using a magnifying glass on the actual breakers. 

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Who's Online   1 Member, 0 Anonymous, 44 Guests (See full list)

  • Forum Statistics

    32.1k
    Total Topics
    437.6k
    Total Posts
  • Member Statistics

    26,009
    Total Members
    3,644
    Most Online
    Joseph b
    Newest Member
    Joseph b
    Joined