Recommended Posts

Posted

No more than any other food safe finish..

 

I started an end grain one today - I'll post when it's all finished up with "along the way" photos..

Posted

Boards look great, Kev.  Do you go straight from the bandsaw to glue-up or do you clean the curves somehow?  Or do you use a template and a router?  I saw that article in FWW or PWW, whichever it was, but I never ended up reading it.

 

Here's one for you, bush...I'm close.

 

clamps.jpg

WA....WOW....UH....What did you say Kev? Yeah, yeah....nice boards..... It's like when the guy on the beach is reeling in something big and you're waiting to see it and someone walks by and you're really distracted for a second or three :blink: ......your thread was almost highjacked with a picture. 

Posted

Sorry for being slow on the update..  Snapped a ban saw blade today and Grizzly isn't open until Monday..  Should have an end grain board to show early next week..

Posted

Sorry for being slow on the update.. Snapped a ban saw blade today and Grizzly isn't open until Monday.. Should have an end grain board to show early next week..

Oh wow that sucks. So when it snaps does it sling the blade crazily around or does it just fall to the ground?

Posted

Wow - beautiful cutting boards. When done the "x" table, i may give these a try. Would it be a nightmare build without a band saw?

 

You could do it with a jig saw and then flush trip with the router..  Should work just fine.

Posted

You could do it with a jig saw and then flush trip with the router.. Should work just fine.

Do you mean make the cut, and than flip the 'mirror image' to the top/bottom and flush with a flush trim/pattern bit?

Posted

Do you mean make the cut, and than flip the 'mirror image' to the top/bottom and flush with a flush trim/pattern bit?

 

The pattern is 1/4" hardboard so, if I were going to flush trim, I would use that.

Posted

How do you like that bandsaw?

Is that the stock blade? If not, is the stock blade crap and need replacing?

 

To me, that band saw is one of the jewels in their line up. It's been a wonderful saw that's easy to set up and has never let me down.  With that said, it is a 14" saw and I don't ask it to do more than it was intended to do.  

 

It's not the stock blade and I really don't recall what came on it.

  • Like 1
Posted

To me, that band saw is one of the jewels in their line up. It's been a wonderful saw that's easy to set up and has never let me down. With that said, it is a 14" saw and I don't ask it to do more than it was intended to do.

It's not the stock blade and I really don't recall what came on it.

Ok awesome. I have been looking into a bandsaw and this seems like a great deal!!

I'm selling a few of my knives to help purchase a new bandsaw in the next month or 2.

Posted

Awesome I can't wait to see these new boards from you!

 

Just one this time.  End grain for those that asked and a little different stripe pattern

Posted

You asked for an end grain version, here it is..  Thanks for the push Steve!

 

First glue up..

 

b6zrdr.jpg

 

Second glue up..

 

ddV6Cx.jpg

 

Getting it flat and laying out the waves

 

xshBQA.jpg

 

Adding some flare

 

iUT9l2.jpg

 

And, a little more flare

 

ellQPx.jpg

 

Walnut edges

 

YWXjkq.jpg

 

Sand flat and trim

 

bm72Bb.jpg

 

At the suggestion of a good friend, another bit of flare was added.  Paduk

 

zWZw3x.jpg

 

Round corners, sand, and add salad bowl finish - 3 coats

 

tVdcIU.jpg

  • Like 2
Posted

Daaaaaang!!! Now that is a beauty! As always that is some impressive work there. I think your friend was on to something with that paduk addition. It gives it a little extra pop.

Are you rounding the edges with a router or hand sand?

  • Like 1

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Who's Online   1 Member, 0 Anonymous, 48 Guests (See full list)

  • Forum Statistics

    32.1k
    Total Topics
    437.6k
    Total Posts
  • Member Statistics

    26,009
    Total Members
    3,644
    Most Online
    Joseph b
    Newest Member
    Joseph b
    Joined