collinb Posted November 11, 2014 Report Posted November 11, 2014 ... at least for the most part But one thing that always concerns me is the back side. That is, how to set things up so that pieces going through do not fall to the ground, but remain flat for a straight cut all the way. Right now what I do is stack things on my workmates behind it to they come off straight. That seems to do the trick. But it is a hassle. What I need to do is find a collapsible rear extension. Something that will drop down out of the way when putting the saw away but which easily pops up for use. Shouldn't be hard to build. Anyone have a recommended/preferred design? (See ... I'm asking first instead of jumping in making mistakes.) Quote
TerryMcK Posted November 11, 2014 Report Posted November 11, 2014 You need the attached folding outfeed table design that Steve "The Jig" Maskery has on his DVD #2 MORE JIGS AND ACCESSORIES from his Workshop Essentials range. http://www.workshopessentials.com/shop/index.php?route=product/product&path=35&product_id=50 Essentially a folding torsion box that fixes to the back of the table saw. No problems with uneven floors to contend with as it is level with the top surface of the TS. On stands you have the problem with the stock pushing them over and they are rarely level with the TS in any plane. This picture just shows you just the first page of his plans overview so no copyright probs There is a heck of a lot more on that DVD and it includes all the Sketchup drawings to go with the DVD. I think PopWood are reselling the DVDs but you can also get them direct from Steve in the UK. 1 Quote
ponderingturtle Posted November 11, 2014 Report Posted November 11, 2014 Why not get something like this? http://www.homedepot.com/p/RIDGID-Flip-Top-Portable-Work-Support-AC9934/100618242 Quote
collinb Posted November 11, 2014 Author Report Posted November 11, 2014 Why not get something like this? http://www.homedepot.com/p/RIDGID-Flip-Top-Portable-Work-Support-AC9934/100618242 That looks useful for boards but perhaps not too convenient for sheets. Thanks. Quote
collinb Posted November 11, 2014 Author Report Posted November 11, 2014 You need the attached folding outfeed table design that Steve "The Jig" Maskery has on his DVD #2 MORE JIGS AND ACCESSORIES from his Workshop Essentials range. http://www.workshopessentials.com/shop/index.php?route=product/product&path=35&product_id=50 Essentially a folding torsion box that fixes to the back of the table saw. No problems with uneven floors to contend with as it is level with the top surface of the TS. On stands you have the problem with the stock pushing them over and they are rarely level with the TS in any plane. This picture just shows you just the first page of his plans overview so no copyright probs Capture.JPG There is a heck of a lot more on that DVD and it includes all the Sketchup drawings to go with the DVD. I think PopWood are reselling the DVDs but you can also get them direct from Steve in the UK. Thanks. Quote
ponderingturtle Posted November 11, 2014 Report Posted November 11, 2014 That looks useful for boards but perhaps not too convenient for sheets. Thanks. I think it would do OK for sheets, you might want to get more than one though. It doesn't have the issue with roller ones either as it can be set at the height of the table and lift up the material if on bends down before it gets there. Quote
Vyrolan Posted November 11, 2014 Report Posted November 11, 2014 That looks useful for boards but perhaps not too convenient for sheets. Thanks. I think it would do OK for sheets, you might want to get more than one though. It doesn't have the issue with roller ones either as it can be set at the height of the table and lift up the material if on bends down before it gets there. I agree with ponderingturtle about the Ridgid flip top thing. It was recommended in another thread and I thought the same thing. The picture online does not do it justice. The top of that thing is actually pretty big. To me, the photo online makes it look like 3" by 6", but it's more like 5" by 15". It's got a lot of surface and could work quite well for sheets. Quote
Tom Cancelleri Posted November 11, 2014 Report Posted November 11, 2014 That folding rigid outfeed support works decently for sheets. I ripped a 48x48 pieces of 3/4 MDF over the weekend for a new extension table I'm building for my saw. Just after the blade and your cut is done there's a little bit of real estate that your workpiece can rest on, along with the flip top rigid outfeed support. Quote
ponderingturtle Posted November 11, 2014 Report Posted November 11, 2014 I agree with ponderingturtle about the Ridgid flip top thing. It was recommended in another thread and I thought the same thing. The picture online does not do it justice. The top of that thing is actually pretty big. To me, the photo online makes it look like 3" by 6", but it's more like 5" by 15". It's got a lot of surface and could work quite well for sheets. And if you are concerned with how it will handle a particular cut, drop the blade down and see how it balances and runs for you If you can smoothly push the whole cut through it seem to be it should be good. Quote
RichardA Posted November 11, 2014 Report Posted November 11, 2014 Maybe its just me, But, I like the idea of constructing a folding outfeed table, for 2 reasons! #1, It requires thought and develops skills! #2, It solves several problems with time, fold up, fold down, move saw. Seems like the improvement of skills is a welcome addition, and makes your thought process work for you for complications further down the road. The added ability of being able to think on your feet for the problems that arise as you build seems to me to be a bonus! 1 Quote
chefmagnus@grics.net Posted November 11, 2014 Report Posted November 11, 2014 You could just do the crazy cousin thing and get another table saw as a outfeed table. I plan on setting up both saws back to back. Before I had a second saw I had a folding rolled outfeed table from Grizzly saw that I got from a dead saw. I worked great. Was a PIA to mount on the DeWalt table saw. Here is a link to the roller outfeed table. https://www.grizzly.com/products/37-Outfeed-Roller-System-For-Table-Saws/G1317 Quote
tim0625 Posted November 12, 2014 Report Posted November 12, 2014 I prefer an outfeed table. Rollers move and fall over. Once you have a table...even a small one, you won't go back. Hey Administrators!!!!.....this is Timwood. I posted on this thread and it came up as "Guest". I've logged off and back on and it's the same. Whaddup? Quote
blkdiamond Posted November 12, 2014 Report Posted November 12, 2014 I built an outfeed-table using the Kreg Universal Bench legs and wheels. This allows me to easily move the outfeed-table for multiple tasks and it can easily move with the table saw if necessary. The Kreg wheels lock down very solidly. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.