Gateman Posted November 29, 2014 Report Posted November 29, 2014 I was recently bumping around in an old store here in Texas when I ran across this plane. It just looked cool to me and it was dirt cheap so I bought it. Now I'm trying to figure out exactly what I have. I thought it was a plough plane, but the blade seems to wide for that. I'm certian that the "fence" looking outrigger is on backwards, but I can't break the screw loose, so I'm going to have to soak it for a bit. There is a screw on the plate in front of the blade that doesn't hold anything down, so I suspect I'm missing a part. The only markings on the plane are "MADE IN USA". The entire tool is metal. Anyone have any idea what I have here? Quote
wdwerker Posted November 29, 2014 Report Posted November 29, 2014 Rabbet plane. I have seen depth stops you can set , that might be missing. Quote
RichardA Posted November 29, 2014 Report Posted November 29, 2014 It looks like a Stanley #78, but Craftsman made one that is almost exactly the same and they numbered it a #79. Stanley normally signed theirs, and craftsman didn't. And the fence is on backwards. On the outside is a bolt hole for a depth stop, and there should be a nicker just in front of the depth stop....... After you get it cleaned up, you can locate the missing parts on ebay, they are not that expensive. It really is a useful plane if you do a lot of rabbiting. You're not missing a blade, you just move the blade from the rear to the front. Quote
wtnhighlander Posted November 29, 2014 Report Posted November 29, 2014 Yep, rabbeting plane. I have one just like it, but missing the fence. Still pretty useful. Quote
Gateman Posted November 29, 2014 Author Report Posted November 29, 2014 I knew I was in the right place! Thanks for the quick replies. After taking everyones input to the interweb and searching around, RichardA hit it - I have the Craftsman verions of the #79. I've located several sources for the depth stop, so I should be able to make it whole again. I'm assuming that the starred wheel in front of the blade is the nicker. Operation seems simple enough - loosen the screw and rotate to the desired depth. I haven't found a manual for this one yet, but I did find a Stanley 78 manual and it does a fair job of explaining the nicker operation. I chased down a little more info on it, from a blog on sawmillcreek.org, from Feb 2012. There was a discussion about a guy needing info and parts for his - good stuff. http://www.sawmillcreek.org/archive/index.php/t-180850.html "Your plane was made by Sargent. The one I have has a Craftsman blade and no marking other than "Made in USA" on the body. It is black and does not have a blade adjustment lever (like the Stanley version - Bob), but I have also seen them in gray. These Sargent planes have the characteristic horn on the front. The "tell" on the Sargent planes is the little rhino horn on the front of the Sargent planes. Sargent's planes (at least of this type) were a step below Stanley's in certain ways: no adjuster for the iron in the regular position, a simpler casting with less ribbing to maintain straightness, etc. But that horn is great. A Sargent fence should fit. If you want to track one down, contact one of the sellers like Walt Quadrato at Brass City Records (call him, don't e-mail him; I don't know why he lists an e-mail address because he doesn't seem to read his mail), Clarence Blanchard at the Fine Tool Journal (e-mail is fine), or Pete Niederberger (PNiederber@aol.com). I'd get a depth gauge, too; in fact, I'd get a depth gauge before I got a fence. One note on the fence: Sargent left a lot of clearance between the top of the fence and the sole of the plane, so they tend to kind of rattle around. You might consider putting a thin subfence on that snuggles closer to the sole of the plane. If this is confusing, try out the fence when you get it. But you might use it for a while before you get either a fence or a depth gauge. I find I use mine just as a rabbet plane a lot more often than I used it fenced and gauged." Thanks again for the help. Now if I can just get the screws free without snapping any off... Quote
RichardA Posted November 29, 2014 Report Posted November 29, 2014 I knew I was in the right place! Thanks for the quick replies. After taking everyones input to the interweb and searching around, RichardA hit it - I have the Craftsman verions of the #79. I've located several sources for the depth stop, so I should be able to make it whole again. I'm assuming that the starred wheel in front of the blade is the nicker. Operation seems simple enough - loosen the screw and rotate to the desired depth. I haven't found a manual for this one yet, but I did find a Stanley 78 manual and it does a fair job of explaining the nicker operation. I chased down a little more info on it, from a blog on sawmillcreek.org, from Feb 2012. There was a discussion about a guy needing info and parts for his - good stuff. http://www.sawmillcreek.org/archive/index.php/t-180850.html "Your plane was made by Sargent. The one I have has a Craftsman blade and no marking other than "Made in USA" on the body. It is black and does not have a blade adjustment lever (like the Stanley version - Bob), but I have also seen them in gray. These Sargent planes have the characteristic horn on the front. The "tell" on the Sargent planes is the little rhino horn on the front of the Sargent planes. Sargent's planes (at least of this type) were a step below Stanley's in certain ways: no adjuster for the iron in the regular position, a simpler casting with less ribbing to maintain straightness, etc. But that horn is great. A Sargent fence should fit. If you want to track one down, contact one of the sellers like Walt Quadrato at Brass City Records (call him, don't e-mail him; I don't know why he lists an e-mail address because he doesn't seem to read his mail), Clarence Blanchard at the Fine Tool Journal (e-mail is fine), or Pete Niederberger (PNiederber@aol.com). I'd get a depth gauge, too; in fact, I'd get a depth gauge before I got a fence. One note on the fence: Sargent left a lot of clearance between the top of the fence and the sole of the plane, so they tend to kind of rattle around. You might consider putting a thin subfence on that snuggles closer to the sole of the plane. If this is confusing, try out the fence when you get it. But you might use it for a while before you get either a fence or a depth gauge. I find I use mine just as a rabbet plane a lot more often than I used it fenced and gauged." Thanks again for the help. Now if I can just get the screws free without snapping any off... Patience grasshopper, It's sometimes difficult to un screw some things........ Wives are a perfect example!... It takes lube, and time! 2 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.