dodgeram99 Posted December 22, 2014 Report Posted December 22, 2014 I am able to get a drum sander. And after some thought I am going with the jet. Here is the rub. Not sure to go with the 16-32 or the 22-44. Has any one ever used either? If so what's your thoughts? I have read online reviews but that didnt help. I don't want to bye the 16-32. And in 6 months wish in went then other way. Quote
Tom Cancelleri Posted December 22, 2014 Report Posted December 22, 2014 I have the Performax 10-20 which has become the Jet 10-20. It's a great machine, however I wish I had most capacity. If you have the room and money I'd so go big and get the 22-44, and if you really wanna go nuts get the Oscillating Drum Sander. Quote
dodgeram99 Posted December 22, 2014 Author Report Posted December 22, 2014 Oscillating drum sander? Quote
dwacker Posted December 22, 2014 Report Posted December 22, 2014 Jet has a Oscillating 22-44 drum sander. I owned this one and wouldn't give it a thumbs up. I would buy a Woodmaster over the jet if you can fit into your budget. Quote
AstroDave Posted December 22, 2014 Report Posted December 22, 2014 I have the 16-32 and I like it from my limited use... I consider the bigger one but this will suit my purposes for now...32" is well beyond anything I expect to sand for awhile. Quote
dodgeram99 Posted December 22, 2014 Author Report Posted December 22, 2014 Holy crap. ODS is bad. I'll have to research those. Is jet the only one who makes them? Quote
dodgeram99 Posted December 22, 2014 Author Report Posted December 22, 2014 Well im sold. The jet ODS is the one for me. Has everything I am looking for. A little more then what I was going to pay. But with the right tool come the right price. Quote
AstroDave Posted December 22, 2014 Report Posted December 22, 2014 Wow PB that WoodMaster is a great looking multi-purpose machine... The thing I really loved was the rip cut capability that was neat and what a time-saver. They have a sale on right now through today! http://woodmastertools.com/save_big_now Quote
dwacker Posted December 22, 2014 Report Posted December 22, 2014 Wow PB that WoodMaster is a great looking multi-purpose machine... The thing I really loved was the rip cut capability that was neat and what a time-saver. They have a sale on right now through today! http://woodmastertools.com/save_big_now I think your looking at their moulder. The sander is just a sander as far as I know. The 5hp 26" sanders are usually under 3K. Quote
dodgeram99 Posted December 22, 2014 Author Report Posted December 22, 2014 The Wm looks like it would work great. But wayyy to big and also on the wallet. Quote
AstroDave Posted December 22, 2014 Report Posted December 22, 2014 I was looking at the 4n1 unit that moulds, planes, sands and rip cuts... The 12" is around $2300 and didn't look much bigger than my 16-32...actually smaller in width. Still expensive if you don't need those features. http://woodmastertools.com/NS/accessdetail.cfm?PID=781 Quote
dwacker Posted December 22, 2014 Report Posted December 22, 2014 Supermax is another line to look at. Quote
Brendon_t Posted December 22, 2014 Report Posted December 22, 2014 I've used the 16-32. I was a big fan. It's out of my price range but I would buy one in a jif if given the opportunity at a great price. Quote
Tom Cancelleri Posted December 22, 2014 Report Posted December 22, 2014 The problem with the 4 in 1 woodmaster is having to change out components to use them. Going from planer to sander requires taking out parts and changing them. I see too much room for error and tolerances being off. Think Swiss Army Knife, ok at everything, master of nothing. Quote
dwacker Posted December 22, 2014 Report Posted December 22, 2014 The problem with the 4 in 1 woodmaster is having to change out components to use them. Going from planer to sander requires taking out parts and changing them. I see too much room for error and tolerances being off. Think Swiss Army Knife, ok at everything, master of nothing. Im to lazy to go through the work and don't have the patients for a open end drum sander. Quote
wdwerker Posted December 23, 2014 Report Posted December 23, 2014 I have had the original Performax 16/32 for many years. Great little machine. I have heard the Jet isn't quite as good. SuperMax is made by the Performax folks. I've been eyeing the 19/32. Any open side drum sander does take some careful set up and there is a learning curve to running one. Trying to take off too much on one pass is your first mistake. Fine abrasive = tiny adjustments but coarse grits will take more. Quote
Trip Posted December 23, 2014 Report Posted December 23, 2014 ==>Oscillating drum sander? Without a platen, what’s oscillation bringing to the table?? Higher FPM at lower grits?? Not sure I get it... Quote
wdwerker Posted December 23, 2014 Report Posted December 23, 2014 The osselation works to reduce the continuous straight line sanding scratches. It also spreads heating & thus heat build up which leads to resin build up on the abrasive. It works pretty good on my Jet 6 x 89" edge sander as well as the little Ridgid belt sander. Quote
Trip Posted December 23, 2014 Report Posted December 23, 2014 I get edge/belt/etc -- anything with a platen... run a wide-belt in the shop... It's sanders with oscillation and no platen that I don’t get. Without a platen, it's a single point of contact setup – just like running a wide-belt in ‘drum’ mode (platen not engaged) --- you get the same short deep scratch pattern as a drum sander. Same goes with heat – I get it for a belt/platen setup, but on a drum -- you've got 6 or 7 feet of belt to dissipate heat --- in a drum, there’s nowhere for the heat to go... ==>Supermax is another line to look at. I've only heard good things... Didn't someone on WTO just get one? Quote
Tom Cancelleri Posted December 23, 2014 Report Posted December 23, 2014 Trip, from my understanding the drum absorbs some of the heat as well as using more of the belt to spread the heat out across the paper. The straight line scratches I think is the biggest appeal to the oscillation. Quote
Trip Posted December 23, 2014 Report Posted December 23, 2014 I should have been more precise in my question…I get the mfg’s claims for benefits of ODS –vs- DS… It’s more about these benefits being observed in a real-world workflow… I’m just thinking about my own experiences with wide-belt sanders. When you configure a WB for drum-only (‘thicknessing’ mode), the platen is lifted so you get single point (well, single line I suppose) contact with the arc of the drive drum/cylinder -- the geometry of the head keeps the follower cylinder/drum off the stock... Note: there are a series of smaller drums/cylinders/rollers still in contact with the stock and the belt, but we’ll ignore those for simplicity… In my mind, when you configure the WB for 'thicknesing mode' it essentially becomes a very large OSD – the only real difference (at least in my mind) is that you’re dealing with 7 feet of belt with forced air cooling. In my mind, it should behave very much like an oscillating drum sander. My point is that thicknessing-mode is generally restricted to low-grit stock removal because of the deep short scratch pattern left by non-platen contact. You really don’t engage the platen until the mid-grits, say 120/150… As you move up through higher grits, you use more platen and lengthen and soften the scratch pattern – the oscillation rate alsoincreases... Just trying to think through the ‘value’ of the O in the ODS – mfg's get a premium for the oscillation, but is it worth it in a drum configuration? Quote
Eric. Posted December 23, 2014 Report Posted December 23, 2014 There's a long thread somewhere in the archives...basically an exposé of a fool's journey into a Jet 22-44 Pro...and then back out of it. I'm too lazy to dig it up, but suffice it to say, I'm extremely happy I don't have that beast in my shop, and so is my wallet. Look into the Supermax 19/38. Best bang for your hobby buck, IMO. Quote
PeteJr Posted December 23, 2014 Report Posted December 23, 2014 My experience with the Jet 22-44 sanding cherry door components is very positive. Understanding the machines capabilities, careful setup and high capacity dust collection are my keys to success. This machine requires patience and practice to obtain best results. Quote
dwacker Posted December 23, 2014 Report Posted December 23, 2014 The ods does make a big difference on finer grits. The issue is the machine always sagging. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.