wtnhighlander Posted December 23, 2014 Report Posted December 23, 2014 After the cutting boards were done, I had a small slab of walnut glue-up leftover. I planned to make a simple pattern-routed dish, but nothing seemed to go right. First, my only pattern bit was too long. Then I didn't have the correct collar to use with my round-nosed bit for the inside corners. Then my largest roundover bit turned out to be too small to make the bottom round enough to look good. Anyway, I hogged out most of the interior with a forstner, freehanded to the line with a straight router bit, and shaped the inside corners with a power carving disk on my 4 1/2" grinder. Sanding THAT out was a serious pain. Simple roundovers on top of the rim looked ok, but it needed more. I used the tablesaw to cut a shallow groove just below the rim, and filled it with home made 'inlace' ( epoxy and gold powder pigment). I made the outside bottom edge more round with power carver, followed by rasps, files, and lots of sanding. Finished with rattle can spray lacquer, Mere Mortals style. The inside went all orange peel (did I mention I hate spray finishes?), so I rubbed it out to a fine mat sheen with Johnson's paste wax, 400 grit paper and steel wool. Here's a photo of the dish in its native habitat: Here are some detail shots: Sorry I have no 'in progress' photos, but if I took 5 minutes setting up a shot, of the 10-15 minute segments of shop time I usually am able to grab, I'd never complete anything! Thanks for looking! 2 Quote
wdwerker Posted December 23, 2014 Report Posted December 23, 2014 Photo Links seem to be messed up. Quote
wtnhighlander Posted December 23, 2014 Author Report Posted December 23, 2014 Photo Links seem to be messed up. Hhmmmm....uploaded from my phone with tapatalk. URL shows tapatalk @ imageshack.com or some such thing. I see them fine, but I'm still on my phone. I'll check from a pc and get back. Quote
Raefco Posted December 23, 2014 Report Posted December 23, 2014 I can see it, it looks very nice. …I just re uploaded a pic that I posted that was showing a broken link Quote
wdwerker Posted December 23, 2014 Report Posted December 23, 2014 I checked back and they work now ! Nice dish! I like the sapwood streak for contrast. Quote
Raefco Posted December 23, 2014 Report Posted December 23, 2014 I was going to give you a hard time about your lathe being out of wack but after that description it, well never mind 1 Quote
wtnhighlander Posted December 23, 2014 Author Report Posted December 23, 2014 Raefco, if that thing had come off the lathe, I'd be bragging for sure! It has it's share of defects, but the womenfolk in the family like it, so I'm satisfied. Steve, thanks and I'm glad the pics came through. My wife likes the sapwood streaks too. Walnut is my favorite material to work with (so far). Quote
Raefco Posted December 23, 2014 Report Posted December 23, 2014 Raefco, if that thing had come off the lathe, I'd be bragging for sure! It has it's share of defects, but the womenfolk in the family like it, so I'm satisfied. Steve, thanks and I'm glad the pics came through. My wife likes the sapwood streaks too. Walnut is my favorite material to work with (so far). I like the streaks also, I'm building a cabinet from walnut that is riddled with sap wood. I glued everything as random as possible, some will like it some will not, my wife loves it, thats what matters Quote
duckkisser Posted December 23, 2014 Report Posted December 23, 2014 did someone say inlay looks good next time play with adding mica powder to the mixture you will get some nice sparkles and highlights to your inlay. thought about making something similar was going to use my hand tools to carve it out then i thought naaaaa where is my lathe Quote
wtnhighlander Posted December 23, 2014 Author Report Posted December 23, 2014 did someone say inlay looks good next time play with adding mica powder to the mixture you will get some nice sparkles and highlights to your inlay. thought about making something similar was going to use my hand tools to carve it out then i thought naaaaa where is my lathe Hey Duck, I don't have a local supplier for those nice minerals for inlay, gonna have to order some one of these days. I did recently discover that "extra fine" glitter from Hobby Lobby adds a nice sparkle to things like crushed MOP or abalone! I want to do some brass or silver inlay sometime. How do you keep the metals from streaking the wood during sanding / polishing? On small jewely pieces, I like to use red rouge on a cotton wheel to polish the wood, but brass and aluminum both leave streaks when the wheel passes over them, so I've never turned out a decent piece with metal inlay. Quote
duckkisser Posted December 23, 2014 Report Posted December 23, 2014 i have struggled with that as well. haven't done many metal inlay just a couple but what i did was get the surface smooth and then i spray shellack over the wood. then i add the inlay . after i sand down the material i spray again for the next treatment of filler. that way if the metal slury (dont know what else to call it) streaks it streaks onto the shellack which gets sanded off when im roughing sanding the project. what i figure is since the rouge has a grit to it to polish your finish what its doing is sanding the metal inlay with a super fine grit and the the metal dust gets mixed with the wax and left on your woods surface. maybe if you seal the surface of your project with a thicker finish and then go back with the rouge it will polish the finish on the surface and not the wood under the project. maybe just use wax and a felt wheel to polish it. i have also found out i rarely use metal with a light colored wood metal slury shows up on maple bad on dark woods its not as noticeable. also try using for something like silver/aluminum use silver soder havent tried it but seen a few videos and pictures and it looks nice. or coper wire just glued into the recess then when you sand it down it sands smooth and fills in the gap. Quote
wtnhighlander Posted December 24, 2014 Author Report Posted December 24, 2014 I considered copper wire for this dish, but I don't like how pink / orange the copper gets when sanded. It would be super cool if there was a way to oxidize the copper without affecting the surrounding wood. Quote
duckkisser Posted December 24, 2014 Report Posted December 24, 2014 I considered copper wire for this dish, but I don't like how pink / orange the copper gets when sanded. It would be super cool if there was a way to oxidize the copper without affecting the surrounding wood. You would have to super carefully tape off around the copper and even the some f those mixtures can be rough on the material might be fun to experiment with it though Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.