Brendon_t Posted January 7, 2015 Report Posted January 7, 2015 I bought a pretty rocking piece of curly maple today at woodcraft for use on an upcoming end table build, I grabbed a freshly sharpened blade for a hand plane and it tore the swirling grain all to hell no matter what direction I hit it from, I'm afraid that if I try to run it through my straight blade delta planer, I will never get a decent surface. Is it feasible to use a drum sander to try to flatten the faces and attempt to get them coplaner? I've never really worked with figured wood. Thanks for input. Quote
wdwerker Posted January 7, 2015 Report Posted January 7, 2015 Drum sander is how I do it. Be careful and take tiny amounts off with each pass. Make sure you keep the abrasive clean, if resin builds up you can get burns. Quote
..Kev Posted January 7, 2015 Report Posted January 7, 2015 What hand plane were you using? I too use the drum sander.. Quote
Brendon_t Posted January 7, 2015 Author Report Posted January 7, 2015 Good to know, I will just progress with that in mind. Just curious, what order do you use for getting the wood S4S? Normally I joint a face then one edge then plane other face then rip the remaining edge. I was using a #5 plane Quote
Llama Posted January 7, 2015 Report Posted January 7, 2015 A #5 is the wrong plane for this. Atleast as it's currently configured. To get better results on figured wood, you want a high angle. This is usually accomplished by using a high angle frog. Or if you are using a low angle plane, you can simply hone a higher angle on the blade. However, since this is in the power tool part of the forum, run it through the drum sander and be done with it How bad was the board when you got it? I don't have any experience with woodcraft lumber. Quote
wdwerker Posted January 7, 2015 Report Posted January 7, 2015 I carefully sand the faces to flatten them, then rip and crosscut on the tablesaw to slightly oversized. You can set up a spiral or shear cutting bit in the router table as a jointer, but practice before you use it to make final cuts. You can also use adhesive back sandpaper stuck to a really flat surface to remove the saw marks on the edges. 1 Quote
Brendon_t Posted January 7, 2015 Author Report Posted January 7, 2015 I know a #5 is the wrong tool but it's the only plane I own besides a block. I figured I couldn't do too much damage just trying it. The board is actually in good shape for not being surfaced at all. Quote
Tom King Posted January 7, 2015 Report Posted January 7, 2015 Probably not worth the effort to set a Jack up to do it. I keep a 4-1/2 set up for curly grain. Super sharp blade. Half a thousandth shaving. Tight mouth for that shaving, and chip breaker filed a little across the end to let it get really close to the cutting edge, but still allow an opening for the shaving. This is where sharp beyond what most people think sharp is really pays off. 1 Quote
Eric. Posted January 7, 2015 Report Posted January 7, 2015 If you're dimensioning curly maple, you may wanna try a toothed blade so you can remove material faster without a ton of tearout. If you're trying to smooth curly maple, follow the advice above...high angle, super sharp. If you have any sense, drum sander. Or Shelix on your planer. Quote
JerrySats Posted January 7, 2015 Report Posted January 7, 2015 I use the jointer and planer with good results. Just take lite passes with each mavhine. You'll want to slow you feed rate on the jointer. At the planer take lite cuts, you can also mist the surface with water, I use a DNA water mixture. 1 Quote
Popular Post wdwerker Posted January 7, 2015 Popular Post Report Posted January 7, 2015 Blood and water would stain the maple red wouldn't it? 3 Quote
JerrySats Posted January 7, 2015 Report Posted January 7, 2015 Blood and water would stain the maple red wouldn't it? Lol the blood would , just so there's no confusion . DNA as in denatured alcohol. Quote
AceHoleInOne Posted January 7, 2015 Report Posted January 7, 2015 Yes to what Jerry said. Never had much to much tear-out on the planer. I you find you like working the figured woods, a drum-sander is a really good Idea. -Ace- Quote
bushwacked Posted January 7, 2015 Report Posted January 7, 2015 Lol!! Hmmm I did not know a drum sander would be best for figured wood. Learn something every day. So the high angled plane mentioned before. Would that be use specifically for figured wood and nothing else? Just curious since I really like figured wood. Quote
Chuck Melton Posted January 9, 2015 Report Posted January 9, 2015 Higher the better... Your motto for life? In all seriousness, I am looking at doing the same thing. I was trying to smooth a piece of curly maple with a blade that I thought was sharp, I was wrong. My sanding options are limited, I was thinking about trying to get most of the way there with an oscillating belt sander and finish with the ROS and hand sanding. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.