gjforeman Posted February 3, 2015 Report Posted February 3, 2015 Trying to bring an old table saw I've been ignoring too long back on-line. It's a contractor type, Rigid 2424, bought in 1999. Very little use in all that time, and the blade to table alignment has been really messed up. But my main concern is the clearance between the blade and the table insert. Every other saw I've seen has the blade centered in the insert slot. This one is barely 20 - thousandths from hitting the arbor side (left side) of the slot. To be centered the blade would need to be at least another 3/16th inch further off the arbor. Yes, this is the factory supplied blade insert, and not my Dado insert. In an attempt to fix this blade shift, and the blade to table alignment, I installed a set of PALS arbor alignment aids, and reset the blade to table alignment with an iGauge, all the while trying to shift the trunion further to the right. After hours of fighting with it, the blade is straight, and again way off center. Any ideas? I checked the manual and the blade is supposed to rest directly on the arbor, but a spacer between them would probably fix it. Thanks. Quote
knotscott Posted February 3, 2015 Report Posted February 3, 2015 If you want to get aggressive, you could turn the saw upside down, unbolt the trunnion brackets, and check that the mating surfaces between the table and the brackets aren't burred or damaged. You might also be able to elongate the holes in the trunnion brackets to allow for more adjustment. You could even hog out the original insert to create more clearance if you want. Otherwise, I'd look to getting the blade as close to parallel with the miter slot as possible, add a new zero clearance insert, and then align the fence with the blade. Quote
wtnhighlander Posted February 3, 2015 Report Posted February 3, 2015 I have a 24241, slightly later version of the same saw. Seems like my arbor has a spacer on it. I'll see if I can tell after work, and let you know. Quote
mikem Posted February 3, 2015 Report Posted February 3, 2015 If the blade alignment is otherwise good, and the only issue is it is too close to the insert opening, I would put a zero clearance insert on instead, and call it day. Quote
gjforeman Posted February 3, 2015 Author Report Posted February 3, 2015 I left a message with Rigid and got an auto reply that they'll get back to me in 72 hours. Probably tell me they no longer support a 2424 or to tell me to buy a new saw. Thanks for the replies. Quote
wdwerker Posted February 3, 2015 Report Posted February 3, 2015 I'm not familiar with that saw, but is there no way to just adjust the top of the saw over and then re-square it with the blade? 4 bolts on the corners of my UniSaw's top allow me to shift an align it. Maybe they built those saws differently ? Quote
mikem Posted February 3, 2015 Report Posted February 3, 2015 The unisaw trunions are mounted to the cabinet. His saw the trunions are mounted to the table, so it does work a little different. Quote
wdwerker Posted February 3, 2015 Report Posted February 3, 2015 No adjustment where the trunions attach to the table? Loosen, shift , tighten ? Maybe there is excess metal inside the holes in the trunions ? Drill or file carefully? Hard to say without seeing it. Quote
mikem Posted February 3, 2015 Report Posted February 3, 2015 I would think there would be, just would be more difficult to get to the needed bolts. Quote
Tom King Posted February 3, 2015 Report Posted February 3, 2015 As simple as it sounds, that's one of the biggest advantages to a cabinet saw. Contractor saws are a pain at best to get dialed in. My old Powermatic 62 wasn't too bad, and holds well, but I've never had my hands on another one that wasn't a royal PIA. Quote
wtnhighlander Posted February 4, 2015 Report Posted February 4, 2015 I found it easier to just flip mine over and remove the cabinet section. All the trunion adjustments are much simpler. Only thing to do from the top side is to set the blade tilt travel stops. Quote
Coop Posted February 4, 2015 Report Posted February 4, 2015 It sounds like you already have a zci, especially if it's tight on the drop off side. Quote
Mzdadoc Posted February 4, 2015 Report Posted February 4, 2015 I re-read the OP and still think the same thing. If it's not hitting and can't hit leave it alone. You sound like me. I tend to over think mechanical stuff. First day of class January 3rd 1985 at WyoTech. "KISS" Keep it simple stupid! Ask yourself is it a problem or is it just a problem to you? Quote
gjforeman Posted February 9, 2015 Author Report Posted February 9, 2015 After a bit of looking, I found a set of 4 different thin shims for a 5/8" arbor shaft at Infinity Tools. Will see when they arrive if they help with the problem. The clearance is so small I'm worried about the blade hitting should I try to tilt it. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.