prov163 Posted February 11, 2015 Report Posted February 11, 2015 I'm ready to buy my first rail and stile bit set. I want to start with Shaker style for a project I'm building for a friend. The Sommerreld set appears great, but it's pricey. I don't mind spending a few bucks to get a great set as I expect to use it quite a bit. What are your recommendations? Quote
Pwalter5110 Posted February 11, 2015 Report Posted February 11, 2015 Im just throwing this out there because im not 100% sure what the best option is, but dont most people just use a table saw for shaker doors? I dont see much need for special router bits, unless I am missing something. Shaker doors, are just square. No real profile, and the panel is cut on an angle on the backside at the table saw. I know a pro will be along to answer this question, but thats my input. Quote
Tom Cancelleri Posted February 11, 2015 Report Posted February 11, 2015 I ordered the whiteside shaker bits the other day. I like the raised panel option for them, and that the bit is meant for undersized 1/4" which is 7/32" Quote
knotscott Posted February 11, 2015 Report Posted February 11, 2015 All my top bits are Infinity or Whiteside (Eagle America is mostly made by Whiteside too). I've heard good things about Somerfeld, but never tried any. Quote
Tom Cancelleri Posted February 11, 2015 Report Posted February 11, 2015 I've got the Sommerfeld Cove Raised Panel bits. They work well and leave a nice clean cut. My Whiteside bits should be here today, I will be making my shaker doors for my shop cabinets before this weekend is over, I can give you more information and some pics after they are done if you'd like. Quote
dwacker Posted February 11, 2015 Report Posted February 11, 2015 Im just throwing this out there because im not 100% sure what the best option is, but dont most people just use a table saw for shaker doors? I dont see much need for special router bits, unless I am missing something. Shaker doors, are just square. No real profile, and the panel is cut on an angle on the backside at the table saw. I know a pro will be along to answer this question, but thats my input. Shaker doors today have a beveled edge. The angle varies by model and manufacturer. The tablesaw thing was a Norm thing. The biggest mistake folks make with doors in general but more so with shaker doors is centering the groove on the door. Quote
Tom Cancelleri Posted February 11, 2015 Report Posted February 11, 2015 Shaker doors today have a beveled edge. The angle varies by model and manufacturer. The tablesaw thing was a Norm thing. The biggest mistake folks make with doors in general but more so with shaker doors is centering the groove on the door. Groove biased towards the front. Shaker raised panel is also really nice. I'm not a huge fan of the bevel on rails and stiles of shaker doors since it takes away from the shadowing effect of the 90 degree. Quote
dwacker Posted February 11, 2015 Report Posted February 11, 2015 Groove biased towards the front. Shaker raised panel is also really nice. I'm not a huge fan of the bevel on rails and stiles of shaker doors since it takes away from the shadowing effect of the 90 degree. The 15 degrees keeps the edges from chipping and getting banged up. Face profile should be 3/8" tall. Quote
Stobes21 Posted February 11, 2015 Report Posted February 11, 2015 Shaker doors today have a beveled edge. The angle varies by model and manufacturer. The tablesaw thing was a Norm thing. The biggest mistake folks make with doors in general but more so with shaker doors is centering the groove on the door. PB, why? Is there any reason other than asthetic to cut the groove off center? Quote
dwacker Posted February 11, 2015 Report Posted February 11, 2015 PB, why? Is there any reason other than asthetic to cut the groove off center? Nope it just looks the best. Some claim its to use eased edge cutters without making the profile appear to thin. IMO it just plain marketing, put a 1/4 profile door next to a 3/8 profile door and the 3/8 will always sell first. The same goes for raised panels. The narrow profile will always look bad compared to the wide profile. The brain just likes the tall wide profiles. Quote
prov163 Posted February 11, 2015 Author Report Posted February 11, 2015 Thanks for all the replies so far. While I know I can create simple doors on the table saw, I think the enhanced look offered by a good set of router bits makes all the difference. PB, what bits do you recommend? Quote
dwacker Posted February 11, 2015 Report Posted February 11, 2015 PB, what bits do you recommend? I have never made a door on a router table so not much help. Whiteside and Freud are both good brands. This is what I use both cope and stick are on the same knife. Quote
prov163 Posted February 12, 2015 Author Report Posted February 12, 2015 PB, doesn't that make a terrible mess? Quote
Trip Posted February 12, 2015 Report Posted February 12, 2015 ==>doesn't that make a terrible mess? No, he's providing scale... The cutter grinds the beans, then heated in HHG pot and strained through a gravity-gun setup into the mug… Quote
prov163 Posted February 12, 2015 Author Report Posted February 12, 2015 Was that a Festool grinder I saw in the background? Quote
ColinF Posted February 12, 2015 Report Posted February 12, 2015 ==>doesn't that make a terrible mess? No, he's providing scale... The cutter grinds the beans, then heated in HHG pot and strained through a gravity-gun setup into the mug… can I get a cup with General Finishes creamer? Quote
dwacker Posted February 12, 2015 Report Posted February 12, 2015 ==>doesn't that make a terrible mess? No, he's providing scale... The cutter grinds the beans, then heated in HHG pot and strained through a gravity-gun setup into the mug… Coffee is required while you watch the wood go through the feeder. Quote
Tom Cancelleri Posted February 12, 2015 Report Posted February 12, 2015 Nope it just looks the best. Some claim its to use eased edge cutters without making the profile appear to thin. IMO it just plain marketing, put a 1/4 profile door next to a 3/8 profile door and the 3/8 will always sell first. The same goes for raised panels. The narrow profile will always look bad compared to the wide profile. The brain just likes the tall wide profiles. Your brain likes certain dimensions, this happens to follow the golden ratio which is found throughout nature. Mathematically defined as Quote
ResidentEvil Posted February 12, 2015 Report Posted February 12, 2015 Nope it just looks the best. Some claim its to use eased edge cutters without making the profile appear to thin. IMO it just plain marketing, put a 1/4 profile door next to a 3/8 profile door and the 3/8 will always sell first. The same goes for raised panels. The narrow profile will always look bad compared to the wide profile. The brain just likes the tall wide profiles. This is a stupid question, but what do you mean by "profile"? Is that the distance the panel is inset from the front of the frame? So a 1/4" profile would have the panel recessed 1/4" from the front of the frame? Quote
dwacker Posted February 12, 2015 Report Posted February 12, 2015 This is a stupid question, but what do you mean by "profile"? Is that the distance the panel is inset from the front of the frame? So a 1/4" profile would have the panel recessed 1/4" from the front of the frame? You got it. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.