Raefco Posted February 16, 2015 Report Posted February 16, 2015 I have decided it is time for a proper router table and I have decided to build one, I have bought 2 sizes of aluminum track, Miter gauge, a Kreg router mounting plate, 2 Kreg feather boards and an assortment of hardware for the fence. I had 20 bdft of hard maple, seems like a good place to start so I milled enough wood to glue up a 22 x 28 top. An assortment of parts for the fence and dust collection port Well, this is where I called it an evening, Too Be Continued Quote
rodger. Posted February 16, 2015 Report Posted February 16, 2015 nice! I just bought/installed a kreg plate and I really like it. Quote
RichardA Posted February 16, 2015 Report Posted February 16, 2015 Darn, Raef.... You done good. Looks like you're going to have a damn nice set up that will last you a long time. Quote
Raefco Posted February 16, 2015 Author Report Posted February 16, 2015 nice! I just bought/installed a kreg plate and I really like it. Which router you using, I'll be getting a new router for this and I'm not sure if I should go fixed or plunge, I've never had a table where I could just pull the whole unit out?Darn, Raef.... You done good. Looks like you're going to have a damn nice set up that will last you a long time. Thanks, have a few parts left to collect but I think it will turn out pretty well Quote
rodger. Posted February 16, 2015 Report Posted February 16, 2015 Which router you using, I'll be getting a new router for this and I'm not sure if I should go fixed or plunge, I've never had a table where I could just pull the whole unit out? Thanks, have a few parts left to collect but I think it will turn out pretty well I use the big daddy freud, ft2200vce. It's a plunger, but I took out the springs to make it a permanent table router. Works great. Quote
wdwerker Posted February 16, 2015 Report Posted February 16, 2015 PC 7518 go big and never regret it! Table looks very good! Quote
Raefco Posted February 17, 2015 Author Report Posted February 17, 2015 Thanks guys, I installed all the aluminum tracks in the table today then I went driving around this evening to see what I sort of router I could get local, The best I could do was a fixed base Bosch 1617 for 140.00 so I picked it up to install in the table. when I installed it, it was not lifting properly, upon inspection I found it was missing a E-clip, seems like a weak design for this use so instead of returning it, I am going to install a nylon bushing and a collet in it place. The clip should be on the bottom of this shaft at the shoulder. I currently have two routers that I really like and they are both Craftsmen 12 amp 1-3/4 hp, one fixed and one plunge both are less then 2 years old, the fixed base was in my cheap-o router table and it was getting hot cutting the hard maple for this table so if the Bosch don't cut it I have to order something bigger, which is what the wife said I should do but I'm going out of town on Wednesday and i'm gonna cut something up with this table before I leave. LOL Quote
bushwacked Posted February 17, 2015 Report Posted February 17, 2015 Is the plate a necessity for a router table? A hole in a nice wood top is not good enough? Or I guess my next question would be .. Does the plate allow for anything extra over a wooden top? Quote
Raefco Posted February 17, 2015 Author Report Posted February 17, 2015 No not totally necessary you could just rout a recess in the bottom of the table, I think that would be minimum so you dont restrict the over all height of the bit. The plate allows you to remove the whole assembly for cleaning, adjustment or what ever. Quote
Brendon_t Posted February 17, 2015 Report Posted February 17, 2015 I just finished building mine and it is awesome to have. I highly recommend ruNning a big electrical switch Quote
ResidentEvil Posted February 17, 2015 Report Posted February 17, 2015 With an all hardwood top like that are you worried at all about cupping or warping of the top? I notice you have support braces on the bottom, did you elongate the screw holes in the cross grain pieces to account for wood movement? Looks good overall. Quote
Raefco Posted February 17, 2015 Author Report Posted February 17, 2015 With an all hardwood top like that are you worried at all about cupping or warping of the top? I notice you have support braces on the bottom, did you elongate the screw holes in the cross grain pieces to account for wood movement? Looks good overall. The top and frame is glued completely solid, it is something like 22" deep and 28" inches wide and its all around 7/8' thick, I did my best to alternate grains and cups when planing and gluing, who knows if it will grow but since it is in a climate controlled basement that varies very little in temp and humidity it has a pretty good shot at staying flat. Quote
dwacker Posted February 17, 2015 Report Posted February 17, 2015 The top and frame is glued completely solid, it is something like 22" deep and 28" inches wide and its all around 7/8' thick, I did my best to alternate grains and cups when planing and gluing, who knows if it will grow but since it is in a climate controlled basement that varies very little in temp and humidity it has a pretty good shot at staying flat. That is actually more myth than truth. Alternating the grain does so little to help it really not worth the time. Not to rain on your parade but the chance of it warping or just splitting down the middle are pretty good climate controlled or not. Quote
Raefco Posted February 17, 2015 Author Report Posted February 17, 2015 That is actually more myth than truth. Alternating the grain does so little to help it really not worth the time. Not to rain on your parade but the chance of it warping or just splitting down the middle are pretty good climate controlled or not. Well, as a hobbyist it really don't matter, it may go 6 weeks or 6 years either way the top is just screwed down and for 30 bucks and a couple hours I can just change it out, I'm sure it won't take long to find something I wish I had done different Quote
Brendon_t Posted February 17, 2015 Report Posted February 17, 2015 I'm of the same opinion use the hardwood as long as the face registers square to your fence and if it ever warps replace it with something else. I used a piece of 2 inch thick melamine that used to be a toolbox cabinet top Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.