Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

2 HP Unisaw 34-450? Upgrade motor?

Featured Replies

There is a 2hp Unisaw 34-450 available on Craigslist. Can the motor be upgraded at a later date if I decide I want a 3 hp? Does anyone have any comments on the 34-450?

If it mounts like the other unisaws I have seen, it has a weird mounting system. If the new motor comes from a unisaw it should. What would the 3 hp give you over the 2?

  • Author

One more hp?

It's not critical really. A small cabinet saw is an improvement over my old contractor saw with crappy fence, so even if this winds up being an intermediate tool for me I would be happy.

Not being a smart ass. I'm genuinely wondering what value you expect from the extra power.

I personally don't subscribe to the more hp the better club. I run a 1.5 every day. Cutting up to 8/4 hard wood and have yet to bog it down. Feed rate of course is slower but it is what it is.

  • Author

I don't take your post as being smartass. It's a legit question, and I don't have a good answer.

There is the bigger is better theory certainly. The standard for single phase cabinet saws seems to be 3hp. It seems to me that there must be a reason, although I couldn't tell you what that would be.

The thickest wood that I have worked with is 5/4 oak and ash so I really don't have any experience to guide me.

There should be no reason you can't mount a 3hp Unisaw motor on it if you want to....it'll boil down to a matter of whether or not the cost and effort is worth it. The 2hp is capable of meeting just about all the needs of a hobbyist, given the right blade and good setup of the saw.  Going from 2hp to 3hp represents 50% more power...it's noticeable and labors less with the same task, but isn't necessary.  It'd also be less sensitive to the blade selection and setup than 2hp.  

I personally don't subscribe to the more hp the better club. I run a 1.5 every day. Cutting up to 8/4 hard wood and have yet to bog it down. Feed rate of course is slower but it is what it is.

 

Arbor speed is always close to 4000rpm on 10" tablesaws they may vary by a couple hundred either way but that little bit does not make any difference. Feed rates are determined by the blade not the saw or saw hp. Reducing feed rate due to lack of HP reduces cut quality and causes burnishing. You may not even be able to see it but its there, no different than over sanding. Having the HP for the optimal feed rate is always a good thing if its within your reach.

Arbor speed is always close to 4000rpm on 10" tablesaws they may vary by a couple hundred either way but that little bit does not make any difference. Feed rates are determined by the blade not the saw or saw hp. Reducing feed rate due to lack of HP reduces cut quality and causes burnishing. You may not even be able to see it but its there, no different than over sanding. Having the HP for the optimal feed rate is always a good thing if its within your reach.

So if you were cutting a 12/4 piece of oak, on a 1.5 hp saw you would plow through it rather than slow it down?

This seems counterintuitive to me.

I know that the arbor speed is pretty constant but the hp behind it to keep up that speed under heavy load is what I believe we're talking about. Slowing down the cut takes less wood with each pass effectively reducing the load and allowing a smaller hp motor to keep up The desired blade speed rather than slowing down.

So if you were cutting a 12/4 piece of oak, on a 1.5 hp saw you would plow through it rather than slow it down?

This seems counterintuitive to me.

I know that the arbor speed is pretty constant but the hp behind it to keep up that speed under heavy load is what I believe we're talking about. Slowing down the cut takes less wood with each pass effectively reducing the load and allowing a smaller hp motor to keep up The desired blade speed rather than slowing down.

 

No its speeds and feeds. Taking less wood at optimal rpm causes burnishing. The blade determines optimal feed rate for 4000 rpm no different than any other cutter be it a jointer, planer, shaper or moulder. No you not would just plow through 12/4 because you can't thus you are lacking HP for the task. The only way you would get through 12/4 at 4000 rpm arbor speed with an optimal feed rate is to increase HP to closer to 15HP.

I think the point PB is making is that when you slow down, the blade will have more of a tendency to burn or at least burnish the cut surface.  That's one of the reasons I've moved up to a 3HP saw.  Having to slow the feed rate down in thicker/harder stock always seemed to result in a poorer cut quality.

  • Author

Well, I did it. Picked up my new (only 36 years old) delta Unisaw.

Managed to transport it in my pickup and get it into my shop. Started cleaning it up , but in truth it needs very little maintenance. I am cleaning as I go, but this tool is in great condition.

Well, I did it. Picked up my new (only 36 years old) delta Unisaw.

Managed to transport it in my pickup and get it into my shop. Started cleaning it up , but in truth it needs very little maintenance. I am cleaning as I go, but this tool is in great condition.

 

Awesome!  I hope you can make a lot of saw dust with it!

Well, I did it. Picked up my new (only 36 years old) delta Unisaw.

Managed to transport it in my pickup and get it into my shop. Started cleaning it up , but in truth it needs very little maintenance. I am cleaning as I go, but this tool is in great condition.

 

i-dont-get-it-where-are-the-pictures.jpg

 

;)

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.