Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

sticky arm r seal

Featured Replies

i made a picture frame and base out of walnut and curly maple.  Applied 1st coat of arm r seal yesterday about 5 30pm.  Its almost seven the next morning.  The thing is still sticky.  Ive used arm r seal a bunch of times and its usually dry and ready for 2nd coat way before now.  My shop stayed over 60 last night and im not sure what is going on.  any suggestions?   thanks in advance

You could dry wiping it down with some mineral spirits to remove the uncured arm r seal.  Alternatively, especially for small things like picture frames, I've used shellac to fix up a sticky finish without stripping whatever it was underneath.

A thick coat or high humidity can slow drying in cold weather especially. If it's still sticky tomorrow night clean it off w mineral spirits.

Out of curiosity, was it their flat finish?  I normally use their semi-gloss and have never had an issue, but for some reason this last order I used the flat, and it was not setting up.  Applied correctly in proper temps and still tacky after a week.  I contacted GF and they were very helpful, but we still haven't figured out the issue.  They sent me a new batch of flat but I have yet to try it.  I applied some semi gloss last night and it set up perfectly..

For me, the obvious issues could be old finish, and temperature.  If it's a small item, bring it someplace warmer like the kitchen and see if that helps it cure.  Also might consider using the same finish on a piece of scrap to see if it has the same issue.

 

  • Author

Its actually the gloss I've only had it about a month and it's been stored inside Sent from my iPhone using Tapatalk

  • Author

ok so i just got home.  It was still sticky so i got a rag and wiped it with mineral spirits then let it sit and then wiped it again and dried with air compressor.  Im not sure what to expect  it still looks and feels like it has finish on it.  Next step?  try another coat of arm r seal?  sand it down? break out the shellac can?  sorry just never had this type of finish fail before and its getting down to crunch time.

I think I'd do another coat of ARS, wait about an hour then bring it inside the house where it's warm to cure overnight.  If that doesn't set up, then another wipe down and hit it with some shellac.  Unless this is something that you're mailing you still have a bit of time :-)

 

Good luck!  Let us know how it turns out!

Are you applying with a rag or brush? 

  • Author

im using a rag  and i applied another coat about 5 yesterday  and its 6am this morning and still have same issue. 

How old is the varnish? Is it humid in the shop? Get some air moving in the shop and see if that helps. You don't want a fan blowing on the project just air circulating. It won't help with dust but might determine if it's the conditions in there. 

I had a similar issue using the satin last weekend. It took about two days to dry. I applied another coat to the project last night and checked it this morning and it was completely dry. I think the difference is that last weekend was very humid and today the humidity is low.

  • Author

I gave up on it and went to shellac probably follow with lacquer. I think it's a bad can. I had a small amount left on a can from earlier and put it on a scrap piece at lunch and it already is dried I've never had this happen with arm r seal

Sent from my iPhone using Tapatalk

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.