Recommended Posts

Posted

I have the Dewalt DW618PK router.

I want to get a router table and a router lift for it.

I found the bosch RA1181
but I'm leaning toward the Kreg PRS2100 with the PRS3000 lift. My question is, how easy is it to take the router in and out of the table and lift? In case I want to use it with the plunger above board? Will this get old? Is this a pain in the rear?

Then I thought, maybe of keeping my dewalt router as my above the board router and getting the Bosch RA1181 with the 1617EVS router and RA1165 and then keeping this as my permanent router table setup.
It would be used for relative light work, round overs and for making frames. The only thing I don't like about this, is I miss my precision router lift. 

But, I'm not sure how much I really need precision lift? I want to make small decorative boxes and signs and small bedside and chair side tables. Maybe the Kreg setup is over kill.

Any advice/guidance?

Posted

Most people around here are running either a Jessem or Incra router table with a 3 1/4 hp Porter cable 75182 (5 speed) router. 

You'll regret or quickly change your mind about changing the router from hand held to table. That is going to get old real fast. Also, having a variable speed option on your router table opens up a whole other level for its usefulness.

I own a Jessem table with the hand wheel lift. I bought the Mast-R-Lift Excel II premium package and threw the 75182 under it. It wasn't cheap, but it's a buy once cry once router table. Does pretty much anything you'd want a router table to do. I got my table package from http://www.pmctool.com/jessem/. The PC 7518 comes as a can only for about $300. and will bolt right in.

I know it's probably more than you had in your initial budget, but just like any other tool that you'll be using for the long haul, it's worth waiting and saving for. 

Incra makes a really nice table as well. The fence works a bit better than the Jessem fence because it moves as a unit from the middle. I just don't have much experience with their tables, but know lots here like them.

 

Posted

I've got the 1617evs and the lift that goes with it!  So far I like it dedicated to the router table, two other routers fill my bench needs, treat it like you care about it, and it won't bite you in the butt!

Posted

As John mentioned above I am one of the ones that have the Incra LS super system and table with the Porter Cable 75182 router permanently mounted.  I am real happy with the set up, it is a real easy fence to move and set u.  It is the last table I will need to buy.  But like he said it is in the buy once cry once price range.  I think you will find in your research that any good lift that is worth having mounts the router in such a way that it is some what of an inconvenience to keep taking the router in and out plus I think to get the most out of your table you are going to what a multi speed, close to 3 HP router.

Posted

Another one here who has a PC 75182 permanently mounted for table use and votes that using one router and swapping out will get old very quickly. Would really recommend saving if need be to make a dedicated table rig. Only thing different is that I'm using the Woodpeckers Phenolic Table with their PRL-V2 Lift, their RF3 fence, and coping sled. Like others, I'm also using a mix of Jessum, Incra, and Leigh accessories top side and bottom side with an Incra dust box (and topside fence) connected the shop's DC pipeline. Way overkill for what you are looking to do most likely. 

Also, like you've seen from others, I keep a couple of other routers around for plunge, fixed, and trim work. It seems like a lot, but I think you'll be less than thrilled with swaps. 

I can't speak to the Kreg table, but their stuff has always seemed decent and definitely worth consideration if you don't want to go back in full tilt. I'd have real reservations about the little bench top Bosch table. In addition to swapping out the router, you'll need a solid work top to clamp it down too...if you're thinking about working on little things, in my experience, the small pieces sometimes need the most solid setups to avoid mishaps. 

Posted

PC7518 in a old Rockler branded lift. Got it secondhand pretty cheap too. Plus there must have been 4 or 500 worth of bits and accessories like feather boards in the cabinet too. Totally lucked into it on Craigslist.

My first big router table was the forerunner to the 7518 but I just bolted the base under a top. Plenty of power & multiple speeds but without a lift it took forever to adjust to the perfect height. I still use the router occasionally for freehand work. Damn thing must weigh 18 lbs and it will wear you out !

Posted

Not to high-jack the thread, but i'm also considering the router table purchase soon.  

I profess that I haven't done too much research, but in order to save floor space in my small 11 x 26 shop, i was thinking about mounting the router table on some sort of structural hinges beneath the overhang on my outfeed table.  As a result, it would swing 90 degrees under the table when not in use (router table plane would be vertical to the floor), and employ folding table legs of some kind to support it when in operation.

Anyone see/use a similar setup or see a problem with storing the router/lift in an 'off vertical' position?

I can draw a picture if my words are less than descriptive.

Thanks - Ted

Posted

You could email the lift manufacturer and ask if they see any problems w horizontal storage. Only issue I see is most lifts and router plates for tables are held in place by gravity . Leveling screws in the corners let you get the surfaces aligned flush but don't hold the lift in place. This is so you can pull the whole thing up if you need to tinker with it.

I have set up counter sections that could be lifted out and a router top put in place. You could have a place it could slide in to store it. Think about fences and accessories needing clearance or you will need to remove them each time. Having to take things apart to store them tends to make you leave them out.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Who's Online   3 Members, 0 Anonymous, 67 Guests (See full list)

  • Forum Statistics

    32.1k
    Total Topics
    437.6k
    Total Posts
  • Member Statistics

    26,008
    Total Members
    3,644
    Most Online
    Bob44
    Newest Member
    Bob44
    Joined