Recommended Posts

Posted

 It does look like a decent saw and at 299 pounds and cast iron wings,,enclosed bace with dust port and left tilt seems nice to me.I think they have good revews also..Did he get the 30in fence?

Posted

He is stepping up from an old Ryobi B3000, so he is excited.  I haven't seen the saw yet.  The model wasn't listed in the add, I do know that it did not have the sliding table that was listed as an option for it.  From the pictures it looks to be in decent shape.  He is coming over today to use my garage (and me) for a brake job.  I am giving him a fold down out feed table and a router. 

Posted

The Supersaw was Jet's response to the early DeWalt hybrid that came out in roughly 2000.  It was basically a good saw available with a couple of options, one of which included a built in sliding table on the left side.  Some complained that it didn't include a miter track on the left side for those with the slider. AFAIK, cast iron wings were standard.    They came with the Microglide fence in a couple of rip capacity options.  The MG fence was onthe mediocre side and got a fair number of complaints for not being on par with a $900+ saw.  

708770.jpg

You're not going to like this, but the Supersaw uses what many describe as a "timing belt" for the blade height mechanism and has a pretty well documented history of breaking those belts.  There are many reports of it breaking multiple times on owners, and that Jet charges a fair amount for an original belt.  There might be some off the shelf replacements that will fit, but the best fix I've seen is to replace the belt and the pulleys with actual chain and sprockets.  (follow the reply from JBushnell here)

A few years ago there was also a second coming of the Supersaw which looked a lot more like a big industrial cabinet saw... some versions offered the MG fence, but the Xacta fence was an option too.  That one had some odd design quirks too, but never made much of a splash.  It was pretty apparent that it was overpriced compared to it's competition, didn't offer much that was unique, and didn't hang around long.

lfabk0r.jpg  

As with any saw, setup and blade choice will make or break it's end performance.  Good luck! 

Posted

The version knotscott shows on legs was also among the saws marketed as hybrids that retained the contractor saw format of table mounted trunnions.  This makes alignment tasks more difficult but, take heart.  A lot of folks have successfully aligned table mounted trunnions and get great results from those saws.

If he reserves himself a Saturday to fully work through the alignment process his time will be repaid every time he uses the saw.  From most reports the saw is a bit under-powered but, this can be offset by using thin kerf, task specific blades; 24 tooth for rip and 60 tooth for cross cuts.  Searching out a source for the problematic belt now, will prevent downtime in the middle of a project later.  It will be up to him whether the investment of the ultimate chain and gear fix is worth the time and effort or not. 

He certainly didn't buy a turkey but, it is a discontinued saw with known issues.  Educating himself to what those are and how others have dealt with them should be helpful.  Info from the forum is a lot more useful before the fact but, there can be just as much help preparing for and resolving problems as well.

Posted

@knotscott and @gee-dub excellent info, thank you both.  Looks like the belt issue is a relatively easy fix with some $20.00 parts,  He is a mechanical kid (35yr old) and wont have any problem replacing the belt with a sprocket and chain.  As far as the table mounted trunnions, I had to go through that "back in the day", I think he should too. :ph34r: 

3 hours ago, gee-dub said:

Info from the forum is a lot more useful before the fact but, there can be just as much help preparing for and resolving problems as well.

Yep, that would be the logical thing to do.  Maybe someday it will happen.  Maybe. It's only been 35yrs, there is still hope.  

  • Like 1

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Who's Online   1 Member, 0 Anonymous, 66 Guests (See full list)

  • Forum Statistics

    32.1k
    Total Topics
    437.6k
    Total Posts
  • Member Statistics

    26,008
    Total Members
    3,644
    Most Online
    Bob44
    Newest Member
    Bob44
    Joined