wtnhighlander Posted November 15, 2016 Report Posted November 15, 2016 Are you saying that the rollers stop turning when they engage the wood? Are they not driven by the same motor that drives the blades? If so, there has to be a gear jumping teeth, a chain jumping its cog, or some sort of clutch mechanism that is slipping. Look closely for a gear that is missing its key or set screws, or perhaps a broken roll pin, if that is how they are attached to the shafts. Simple friction can make the rollers turn with no load, but when they work against the wood, friction will be overcome, and an un-pinned shaft will spin in the gear hub. Quote
Pete Staehling Posted November 15, 2016 Report Posted November 15, 2016 9 hours ago, wtnhighlander said: Look closely for a gear that is missing its key or set screws, or perhaps a broken roll pin, if that is how they are attached to the shafts. In the first picture it looks like the shaft may be missing a key. I'd look at the one first. Quote
Doomwolf Posted November 15, 2016 Author Report Posted November 15, 2016 Turned it on this morning and looked at the other side while I fed wood in. You'll see two gears in the picture - the small one is driven by the motor, and the large one runs the drive chain to the rollers. The large gear skips/stops under load (actually, I can make the gears skip by turning both rollers with hand pressure). I would assume that the fix for this problem is a replacement gear. Also, I tried searching the model number on Sears Direct and Google, and I get zero hits - absolutely nothing. So it's either really old, they made a separate model number to sell this in Canada, or it is unicorn & is the only one of its' kind in the wild. Yayyy..... Craftsman 351.275210 is anyone thinks they can one-up me. Quote
Jfitz Posted November 15, 2016 Report Posted November 15, 2016 Looks stripped. You can always pull them off (both gears) and just take them to a local machine/hardware place.....see if they can look up equivalents. Exact replacements might not be necessary - slightly larger/smaller gears would just change the speed of the rollers. I would think the sum of the radius of each gear would have to be the same though - so the center-to-center distance is the same.... 1 Quote
drzaius Posted November 15, 2016 Report Posted November 15, 2016 The shaft or bearings may be badly worn as well, allowing the gears to move further apart. May not be practical to repair this. 1 Quote
Doomwolf Posted November 15, 2016 Author Report Posted November 15, 2016 I'm thinking I might relist it on Kijiji for parts/as a project for someone (with a full disclaimer). Tonight I'll see if I can pull the gears off and have a look. What I'd really like to be able to do is pull the whole top cover off, but it's on pretty solid - there's probably a nut I missed somewhere, but I don't see how or where. Quote
Jfitz Posted November 15, 2016 Report Posted November 15, 2016 I think you should buy a 3D printer to make any and all replacement parts needed. Quote
Tpt life Posted November 15, 2016 Report Posted November 15, 2016 Pull the gears. Prior posts likely have it right that there is a worn bushing that is allowing the one shaft to wander. Quote
Doomwolf Posted November 20, 2016 Author Report Posted November 20, 2016 @C Shaffer and @drzaius seem to be onto something - I pulled the gears off, and the shaft that the large one is on has a LOT of play in it (it's the bottom of the two de-geared shafts in the one pic). I cannot see anyway to actually remove the shaft, or for that matter, take off the cover of the unit. I've removed every screw and Allan key* I could see that might possibly be holding it on, but it ain't moving. The only thing I can think of is maybe I need to take the rollers out to take the top off? Thoughts? *while cursing the engineer who decided to put Imperial AND metric on the same unit. Quote
Tpt life Posted November 20, 2016 Report Posted November 20, 2016 I hope you get this sorted. There are so many variables at play here. Thin sheet metal, keys, bearings, bushings... Just take lots of pics as you get deeper. It never goes well if you cannot put it back together. 1 Quote
Doomwolf Posted November 21, 2016 Author Report Posted November 21, 2016 Well, currently I'm stuck because I can't find much else to take off without entering the realm of complete dis-assembly. Quote
Doomwolf Posted March 8, 2017 Author Report Posted March 8, 2017 Reached out to a couple of local shops that do work on machinery, but they said this isn't the sort of job they'd so. And so ends the saga..... http://www.kijiji.ca/v-power-tool/ottawa/craftsman-12-5-planner/1245110880?enableSearchNavigationFlag=true Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.