Recommended Posts

Posted

I picked up a planer today off Kijiji, but committed the cardinal sin of not seeing if it turns on before handing over the money. So, having recognized that I was an idiot, does anyone have advice on trouble shooting this? I only paid $100, so even if I have to sink some money into this it's still cheaper than buying new. 

The unit in question is an old, all metal Craftsman 12;5" planer. I've attached some pictures. Issue is simple -you flick the on/off switch as much as you want, it don't turn on. There's a 'circuit breaker' button next to the switch. I hit it a couple of times, and tried a different plug, but no dice. 

IMG_5537 (1024x768).jpg

IMG_5538 (1024x768).jpg

IMG_5543 (1024x768).jpg

IMG_5545 (1024x768).jpg

Posted

I'm with coop, look at the switch first. after that i would look online for a parts diagram, once you find the problem clean it up, oil, grease, check bearings, major cleaning of all parts and planer bed. i wouldn't throw much money at it until you know if parts, knives ect. are available, good luck with it and let us know how it comes out.

  • Like 2
Posted

I had bought a used Craftsman planer a couple years ago.  It ran like a champ, but I found the bolts holding the knives in place to be frozen (I stripped three of them and couldn't remove a single one) and found that I could not source replacement blades anyway.  I resold it and got most of my money back.  

Posted

I have a 15-20 year old Craftsman planer. As Dave (Treeslayer) said, check for parts to see which are available. I think I used Sears Parts Direct. With mine, most of the important stuff is still out there. I needed a safety shield and that wasn't available, so I made one out of some sheet metal. The knives shouldn't be a problem. You can, more than likely, get aftermarket ones that match the dimensions. Check the manual for the size or measure the ones in your machine. You'll probably want a knife setting gauge when you get new knives.

I don't know a lot about small electric motors, but it stands to reason that you can check the switch with a meter (I'm sure there's something on youtube). If that checks out, check the motor. If it's bad I don't think that's necessarily a show stopper. The motor may be available on the Internets for a reasonable price, you never know...

All that said, my planer works well(and yours looks like a newer/better model). I get 2.5" to 3" of snipe on each end of a board, but I plan for that and it isn't a problem other than wasting precious lumber & $.

Oh,forgot to say...You might see if it had infeed/outfeed tables available.

Posted

Are we talking about a multimeter to make sure there is current flowing through the switch?

Will check the internet for a manual this weekend.

Thank you for all the tips guys.

Posted

Yes,  you need a meter to check voltage and resistance.  

I would first check resistance across the switch when off, should read ofl or inf or open. flip the switch and you should get a reading. if the circuit stays open when you flip the switch to on,  then the switch is not switching.

If switch reads ok, let us know and we can keep going with the troubleshooting 

Posted

Hard to tell from the pic, but 120 volt single phase and no visible capacitor says "universal motor" to me. Good chance you have a worn brush, or a brush stuck in its holder, nit making contact with the commutator bars. I recently repaired a scroll saw with the exact same symptom, just by freeing the stuck brush.

  • Like 2
Posted
1 hour ago, Doomwolf said:

Dad and I are frigging around with it right now. Problem seems to be the breaker or the switch, motor runs fine when you hotwire it.

That's good. I think.

Posted

So $11.30 at Busy Bee for a new switch and now it turns on fine.

New problem - the feed rollers don't seem to be engaged. I've attached pictures below in case that helps at all. I ran the thing with the one side panel off (very carefully!), and the gears/chains are spinning, but when you try and feed wood in they stop/lock up/something. Basically, they don't engage. Anyone dealt with this before? The guy did mention that the last time he used it the rollers didn't work well.

 

 

 

 

 

IMG_5550 (1024x768).jpg

IMG_5551 (1024x768).jpg

IMG_5549 (1024x768).jpg

IMG_5548 (768x1024).jpg

Posted

The bed of the planer looks a bit corroded. Is it possible you're just getting too much friction so the rollers can't move the wood? Maybe try cleaning it off and using some wax.

Posted
Cleaned the bed with Teflon and vinegar, and put some paste wax on.

 

TIODS- can use denatured alcohol? it's the only non-drinking type I have.

I can't see any reason that denatured alcohol wouldn't work.

Posted
17 minutes ago, Doomwolf said:

Cleaned the bed with Teflon and vinegar, and put some paste wax on.

 

TIODS- can use denatured alcohol? it's the only non-drinking type I have.

Should work fine.

Posted

Fiddled around and ran some ash through it. I'm going to say that the issue is probably the rollers not being at the proper height/alignment. Quality of cut seems to be good, so the knives are ok. If I track down the manual is it likely to have specs as to how high the rollers should sit in relation to the cutting head?

 

Edit-I can plane stuff with it now, but only by doing all the feeding manually.

Posted

Although it's progress,  it's still not a good alternative. 

Thinking out loud here but I am guessing the roilers are too high not putting enough downward pressure on the board to feed it through both spinning blades and a friction riddled bed.  A dry bed can actually create a lot of resistance.  A bit of wax on the beds and tables and clean rollers can be an amazing help.

Being that those combined are about a 10 minute job,  I would start there.  get the easier thing out of the way.  then move on to more complicated.  

On a side note,  there definately should not be that much slack in the roller drive chain.  

  • Like 1
Posted

Bed has been cleaned and waxed. I attempted to clean the rollers with DNA, but that did not seem to help matters. Doing some Google searching, some advice I saw in an old post on another forum was to soak some 400 grit sand paper in DNA and give the rollers a wipe down (apparently this is how you dealt with feed issues in a manual type writer). I'll give that a try in the AM.

How does one tighten up a drive chain? I'll note that I can't fully rotate the rollers by hand. They are spinning when you turn it on, but stop when the wood hits (both sides panel s are off, being very careful when I start it up).

If nothing else this is turning into a good learning experience.

Posted

Don't confuse DNA with DNA and get too close to the blade:(! I think now that you have the switch problem resolved, you'll find your problem/solution in the rollers and table.  Good luck bud. 

Posted

There should either be a tensioner which I dont see, or a way to spread the rollers further away to take up the slack. do you see anything like that?  

There's also the chance that the chain is stretched but I doubt it would stretch that much. 

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Who's Online   3 Members, 0 Anonymous, 68 Guests (See full list)

  • Forum Statistics

    32.1k
    Total Topics
    437.6k
    Total Posts
  • Member Statistics

    26,008
    Total Members
    3,644
    Most Online
    Bob44
    Newest Member
    Bob44
    Joined