Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Blothcy Gel stain advice

Featured Replies

Hi All,

I'm finishing a table which I think might be maple and having a few of those dreaded blotching issues. I'm hoping I can salvage as time is tight to start all over. Here's where I'm at...

All old finish was sanded off and the scratches sanded out. (The table was a beast to sand in the first place and I ended up going to 600 grit just to get the marks out. Then Bullseye sealer (diluted with equal parts denatured alcohol) was applied very generously so I could sand that without going back to the wood. I sanded again with 320 to give some roughness back for the gel stain, then applied the General Finishes gel stain. The pic below is after three coats. I've since applied an extra one and i now think it looks a little worse. I was hoping the gel would even out much better and I even tried applying it to just the lighter areas but it's not working. Should I just lightly sand with 400 grit and try applying again?

 

IMG_9574.jpg

 

I may be way off here, but 600 and 320 grit sounds too fine.  You want the grain to be able to absorb the stain. I seldom sand to finer than 150 to 200 before staining or finishing depending on the wood. Anyone - feel free to correct me if I am wrong.

If that is an oil-based stain, I'd try wiping it down with mineral spirits first. Might remove a lot, and save some sanding.

I actually just did this last week. I used mineral spirits on a shop towel and gently rubbed the darkest areas of a coat of gel stain to lighten them up a hair. Worked well enough for me, but then I did apply another more consistent coat on top of that layer before all was said and done.

Have you considered applying the finish with an HVLP? Before this post I have never considered using one for gel stain before, but it would likely distribute the color more evenly. Might have issues with wiping up the excess causing the same blotchiness, though. Not sure about that idea, just tossing it out there - one of the mentors will probably explain why it's not a great idea, haha!

2 hours ago, Ronn W said:

I may be way off here, but 600 and 320 grit sounds too fine.  You want the grain to be able to absorb the stain. I seldom sand to finer than 150 to 200 before staining or finishing depending on the wood. Anyone - feel free to correct me if I am wrong.

I don't think it should matter much, given that they're using a gel stain which doesn't really penetrate the wood.

Susan, I had some trouble with this not long ago while staining trim with GF Georgian Cherry. I found that applying a thicker layer actually helped even out the color. If you wipe too much off, you'll end up with streaking and blotching.

I'm wondering, first are talking about a gel stain, or a GF gel Topcoat?

what is your sequence for actually applying the finish? do you typically start applying your coat from one end and then begin whipping up from the other? I'm curious if a small amount of delay or difference in time the stain was applied resulted in one side becoming darker? I'm not really seeing blotchiness so much as one side simply being darker than the other, but that could be just me.

Just went over to general finishes site and reviewed their materials. I found this video quite good. Some keys:

  • Don't over-sand, she recommends only taking it to 150 grit.
  • She applies a skimcoat of mineral spirits before the gel stain.
  • She applies the stain and immediately begins removing the excess with clean rags as soon as she is done applying. There is no delay at all.
  • The top coat gets similar treatment. Removal commences as soon as the board is fully covered.

I've had good luck with GF products, so hope this helps.

 

  • Author

Thanks for all your comments. I initally sanded to 600 as it was the largest grit I could go to get a decent sand on this piece, which was shocking. It's been a nightmare to work with, and maybe that's the problem right there.

BonPacific - It's difficult to put on a really thick layer with such a big piece that has to be stained in parts as you are more likely to see joins if you don't rub a certain amount off. And Denette Unfortunately you can't use a sprayer with gel stain, it's too thick.

Sanding to 320 was actually recommended to me from the fine folks at Woodcraft (after applying bulls eye seal coat to help with the blotchiness), and also a (different) online video from General Finishes suggested 400 (although the can suggests 150 but that's maybe without a seal coat). So, I put on a thick seal coat so I'd have enough to sand back to 320.

I also used 320 with the legs and base parts and they came out SO WELL after staining. You can tell they are a different species of wood, not as hard.

Today, I did another light sand and another layer of stain to try to even things out and I've decided this is as good as it will get. I've attached a picture of the legs too and the difference is big. The legs have had one coat of gel, the table 3.

Honestly, if I was working a piece again, and had pre stain issues, I would not recommend any type of staining, just finishing. That's how the table was originally. I've never had so much trouble before.

If anyone has any other ideas, I'd love to hear!

 

IMG_9590.jpg

IMG_9591.jpg

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.