Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Humidity

Featured Replies

  • Popular Post

What is the humidity range in your house?

The point is, you want to match your shop conditions as closely as possible to the conditions where the piece will live the rest of its life.  Obviously if you're shipping pieces across the country this will be impossible, and frankly, unless you're in a basement or an otherwise perfectly sealed and conditioned shop the way your house is, you'll only be able to get close.  Fortunately, close is good enough.  Use properly dried lumber and follow proper acclimation and milling procedures, build your furniture with movement in mind, and you'll be fine.  Once you understand how and why wood moves, your fight with movement turns into more of a dance.

I use various temporary lights when selecting stock and finishing in order to emulate the eventual setting if I am lucky enough to know it.  The same luxury of knowledge is rarely available in regard to humidity in my experience.  You just can't tell what someone is going to do with a thermostat :).

If I know a piece is going to a native of my area (you'd be hard pressed to pry folks who favor the desert basin out of their holes) I can use pretty tight tolerances on drawer openings and door clearances.  Around here, inset trays for boxes or piston fit drawers can be tight enough to require vent holes in the design and never give you trouble throughout the year.

If I don't know where a piece is going or may end up, I fall back on traditional methods of dealing with wood movement.  Floating tenons at the rear of web frames that ride in dados, ship lap or T&G floating slats for backs, 1/8" clearance around doors and drawers, floating panels door and carcass construction, sliding dovetails on breadboards and stuff like that there.

I am in the chicago area.  My indoor RH% is ranges from 25% in winter to 60%+ in summer.  I run HVAC 24/7.  Literally.  If I am not running heat, I am running AC.  Sounds crazy, but with our  climate and a full wall of south facing windows, my house gets uncomfortably hot on sunny days, even if it is only 60F outside.  

Our actual outdoor RH is relatively constant.  The large fluctuation in indoor humidty is do to forced air heating, which dries the air quite a bit.  I do have in line humidifiers and they help, but can only do so much.  I just installed two new ones and $1000 later I was able to get my indoor RH% up to about 35%, so that is winning.

My garage is heated but poorly sealed, so I do get more outside air/humidity in the garage.  My garage RH% tends to be more stable - usually between 40% and 60%.

The idea that "modern HVAC" creates a more stable environment for wood is a fallacy, in my experience.  Modern heating systems actually create kiln-like conditions that don't naturally exist in a northern climate like mine.  

56 minutes ago, Mike. said:

I am in the chicago area.  My indoor RH% is ranges from 25% in winter to 60%+ in summer.  I run HVAC 24/7.  Literally.  If I am not running heat, I am running AC.  Sounds crazy, but with our  climate and a full wall of south facing windows, my house gets uncomfortably hot on sunny days, even if it is only 60F outside.  

Our actual outdoor RH is relatively constant.  The large fluctuation is do to forced air heating, which dries the air quite a bit.  I do have in line humidifiers and they help, but can only do so much.  I just installed two new ones and $1000 later I was able to get my indoor RH% up to about 35%, so that is winning.

My garage is heated but poorly sealed, so I do get more outside air/humidity in the garage.  My garage RH% tends to be more stable - usually between 40% and 60%.

The idea that "modern HVAC" creates a more stable environment for wood is a fallacy, in my experience.  Modern heating systems actually create kiln-like conditions that don't exist in a northern climate like mine.  

Yup, I have the same thing where I flip off the heat only to turn on the AC immediately after. There really are almost no days where I can comfortably go without one or the other.

Mine is an older house, with boiler/radiator heating on the first floor and finished basement. The 2nd floor has an air handler. I do notice in the winter the air is noticeably dryer upstairs. I wish the boiler covered the upstairs as well, but alas, we can't always get what we want.  

13 hours ago, Eric. said:

 Once you understand how and why wood moves, your fight with movement turns into more of a dance.

How it moves depends on what kind of music you are playing.

Whenever you heat air, you will drop the relative humidity.  The colder the outside air is, the more you have to heat it to the same comfortable room temperature.  The greater the outside air temperature to room temperature ratio, the greater the relative humidity drop.

I thought you guys with 4 seasons only used the HVAC in two of those? I take back everything I thought of you;)

31 minutes ago, K Cooper said:

I thought you guys with 4 seasons only used the HVAC in two of those? I take back everything I thought of you;)

We have four seasons, but 2 of those seasons only last for about 3 days.  

Us too and one of those was today. However, the local Chamber of Commerce has extended it thru Feb. 5th to include SuperBowl. Count on it;)! 

  • Author

When I started this thread the humidity in my shop was holding at 70- 75% with a dehumidifier running constantly. In the last 3 or 4 days, it has dropped to under 50% with the dehumidifier off. Not sure what made the difference.

4 hours ago, freedhardwoods said:

When I started this thread the humidity in my shop was holding at 70- 75% with a dehumidifier running constantly. In the last 3 or 4 days, it has dropped to under 50% with the dehumidifier off. Not sure what made the difference.

The temperature of Odon, Indiana was a high of 67 to a low of 50 on January 21, today it has been between 23 and 32.  Assuming the temperature in your shop when you measured the humidity was approimately the same on both days, then having to heat the air from 67 to 72 is only 5 degrees versus, heating the air from 32 to 72 which is 40 degrees while the difference from 23 to 72 is 49 degrees.

When you heat air, you drop the relative humidity because the air expands so the amount of moisture relative to the amount of air drops.

  • Author
7 hours ago, Hurricane Dry said:

The temperature of Odon, Indiana was a high of 67 to a low of 50 on January 21, today it has been between 23 and 32.  Assuming the temperature in your shop when you measured the humidity was approimately the same on both days, then having to heat the air from 67 to 72 is only 5 degrees versus, heating the air from 32 to 72 which is 40 degrees while the difference from 23 to 72 is 49 degrees.

When you heat air, you drop the relative humidity because the air expands so the amount of moisture relative to the amount of air drops.

 
 
 
 
 

I understand about heating air. I have been keeping the shop at about 55*. If it was 72* in there, I would be making the humidity from all the sweat dripping off of me. :rolleyes: We rarely have our house above 64* or 65* I wasn't even running the shop heater the few days it was warm.

The humidity was 70% in the shop when the outside air was in the low 40s before that warm spell. It didn't vary more than 3 or 4 points for the last 2 weeks no matter what the outside temp until a few days ago. SHRUG.gif

 

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,009 Total Members
  • 3,644 Most Online
  • Joseph b Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.