Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Static charges

Featured Replies

On 3/2/2017 at 4:53 PM, drzaius said:

Lots of people use PVC cause it's cheap, available & easy to work with. If you have very low humidity you might get the occasional zap.

This good point was raised in another thread but when I saw it something popped into my mind:

How many of you ground your ducts?  Static + dust is a dangerous combination, not at all limited to grain elevators.

It's not likely a problem for the periodic user but in a shop seeing constant use, running all day ...

Plus it can eliminate those zaps.

I've been running my system ungrounded for almost a decade and I'm still alive. Shops exploding and burning down because of ungrounded PVC is a myth until someone can show me one proven case of it happening.

 

Sent from my SCH-I545 using Tapatalk

 

 

There have been a number of reasonably serious studies done on whether PVC duct poses a risk either for personal injury or fire/explosion & all have come up negative.

The occasional zap can be mildly painful, but not dangerous. I've gotten zapped off the vacuum hose & it is annoying.

Please don't perpetuate this myth.  It is a scourge on woodworking forums.  The particle density required to cause combustion is way beyond what an air breathing life form can endure.  Even if you could create the environment that would allow a static spark combustion in your shop, you'd be dead way before it happened ;-)

  • Author

Thanks guys for the info.

I was actually thinking that a static charge might be worse for my garage stereo than an explosion.

 

Sent from my MotoE2(4G-LTE) using Tapatalk

 

 

3 hours ago, Eric. said:

I've been running my system ungrounded for almost a decade and I'm still alive. Shops exploding and burning down because of ungrounded PVC is a myth until someone can show me one proven case of it happening.

 

Sent from my SCH-I545 using Tapatalk

 

 

My grandpa ran a factory that produced some of the first composite wood - I think it was OSB or fiberboard, but I couldn't swear to it - and says that on an industrial scale static buildup and subsequent discharge and combustion is a risk.  But he was working in an entire factory that produced nothing but gobs of small particles, so I bet static was a huge problem for him.  I'm willing to bet that I can't make a whole factory's worth of static and blow myself up with my 2hp Powermatic dust collector running on 120 volts.

The dust concentration required is very high. A 60W light bulb cannot be seen from something like 2 meters away in a concentration high enough to pose a hazard.

I was getting the occasional extremely mild zap now and again whenever I touched any of the piping PVC or flex hose, so I ran foil tape right from blower housing along all pipes to the end of each pipe about 1" thick. Didn't bother with the very little flex hose I have around 4.5ft and no more little zaps.....nothing nadda zilcho..... is it grounded properly? probably not to most standards but I got no more little zaps so good enough for me....

  • Popular Post

When I leave my empty beers cans laying around, I get a lot of static from my wife

The dust concentration required is very high. A 60W light bulb cannot be seen from something like 2 meters away in a concentration high enough to pose a hazard.

 

That's pretty close to spot on Doc. Looks like you might have done your research.

 

I've been working in environmental remediation/abatement industry for years as a contractor first and now I'm an environmental consultant. That being said I've worked alot with combustible dust in rubber, plastics, aluminum, and coal. When I used to remove to com dust we used vac trucks or trailer mounted vacs. We never used grounding wires or speciality piping when doing the cleaning. Only the vac system itself was grounded because that's where the highest accumulation of super fine particles are found. Yes the occasional electrical discharge would occur but all the grating and steel super structure is grounded as well. As far as fear of an actual explosion, our fears were very slight, because com dust explosions are actually caused by a secondary explosion at a facility. Where by a small initial explosion shakes the facility and releases all of the fine particles into the air that then mix when the original fire and cause a huge explosion (check the Dixie sugar plant explosion circa 2007 or 2008?).

 

For those that want to do some light reading before bed check out NFPA 654. It's like watching wood dry.

 

*soapbox over*

 

Sent from my SM-G930V using Tapatalk

 

 

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,009 Total Members
  • 3,644 Most Online
  • Joseph b Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.