Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Sad teak outdoor furniture with a past - advice?

Featured Replies

I am the new owner of some 12+ year old teak patio furniture. The former owner stained it with some kind of thick wood stain (I assume NOT made for teak). The set was then pressure washed in an attempt to remove said stain. This appears to have somewhat worked, but they are splotchy where some of the stain was left in the grain. It's dry, cracked in areas, and ugly.

So now as the new owner, I tried to sand the tabletop to remove the mess and quickly realized sanding the HUGE table and all 6 chairs was far more of a project than I was willing to take on. I tried a small patch with teak oil and learned that won't work since, of course, the old stain shows through in places and it still looks splotchy.  

So, what would you do?  (Yes, I know - you would sand it. ;)  Although I MIGHT sand and save the tabletop, I just don't have it in me to sand all 6 of those huge chairs.) It will live on a covered patio and I just need it not be ugly. I know, under normal circumstances, that one does NOT paint or stain teak - but this is far beyond normal circumstances at this point. When sanding is not an option - what do you recommend?  Is there a stain or paint that could make this mess usable?  (And what should I do to the small area I put the teak oil on to prep it for the new.....paint/stain/whatever?) 

Thank you!! <3

Why sanding is not an option? Get a ROS if you don't already own one and get it done. There's hardly anything more relaxing than sanding a table top with a ROS (?)

For this kind of stripping, I'd pick up a cheap belt-sander (the $49 Ryobi works great). That can get a lot done on flat surfaces like a tabletop. Get some aggressive grits (80 may be fine, but you can step down to 50 or even 36) and throw on a podcast.

I don't think there's a stripper on the market that is going to pull all that old stain out of the wood... Or at least that doesn't require a hazmat suit while applying it.

  • Author

I do have a ROS and a belt sander, thank you both! :) If it was just a table, I would do it. But it's also six very large chairs with lots of slats and arms and nooks and crannies. A sander won't even fit in many areas of the chairs. I may sand the 6 foot octagon table, but I do not have the time or patience to sand all of those chairs. Plus, I'd like to be able to use the set sometime this spring - and if I have to find the time to sand the beegezus out of all of those chairs, it'll be well into Summer (or later) before it is usable! 

I'll snap a photo of the chairs when I get home tonight so you can see what I'm up against. Even painting or staining them will be a major PITA, but I can deal with that. IF I can find a product to do the job. 

 

Since you figured out already this job will be a major pain in your ass, which in all honesty is! Look-up a local paint strip company that has dipping tanks. 

 

-Ace-

The other option would be to get a grinder and use a wire brush and scotch brite type pads.  This would be for the heavier stuff, and then sand.

I wonder how soy gel would work? I always see it being touted online and in old house magazines.

 

 

I can't imagine why you would do this though

 

 

Sent from my iPhone using Tapatalk

36 minutes ago, Woodenskye said:

The other option would be to get a grinder and use a wire brush and scotch brite type pads.  This would be for the heavier stuff, and then sand.

A drill probably has better variable speed control, but the wire-wheel is a good suggestion. I've stripped the rust off a cast-iron stove with one of those, so it should handle teak no trouble.

12 minutes ago, Jer32383 said:

I wonder how soy gel would work? I always see it being touted online and in old house magazines.

I can't imagine why you would do this though

I wouldn't trust any recommendations from This Old House or any other similar magazine, they seem like nothing but ads these days, in the articles and next to them.

  • Author

Here are some pics! THANK YOU for your ideas!

The first is the chairs in their current state. The second is a close up of the stain that didn't come up when they power washed them. The third is an arm with some teak oil on it - an experiment on my part. 

Although they surprisingly don't look that bad in this pic, the chairs in their current condition are not acceptable. 

20170320_163314.jpg

20170320_163318.jpg

20170320_163327.jpg

  • Author
Just now, BonPacific said:

Sandblasting? Just a random thought.

Although it could work, I don't think that is in my skills or equipment repetoire. :(

1 minute ago, NashvilleDIYer said:

Although it could work, I don't think that is in my skills or equipment repetoire. :(

Do you have a compressor? The Harbor freight models only cost $20-$30. Their return policy is pretty good if it doesn't work.

I wouldn't trust any recommendations from This Old House or any other similar magazine, they seem like nothing but ads these days, in the articles and next to them.

 

Sorry, not this old house specifically. Ive seen it in restoration magazines, or "old house" magazines. I've also seen a lot of positive reviews online. Looked into it for my house. Never used it though.

 

I think a wire wheel or those paint grinding discs may ruin the wood. I'd be careful. Sand blasting will work but you need to know what media to use and pressures.

 

 

Sent from my iPhone using Tapatalk

To be honest that doesn't look like too hard a job to sand it - just get the flats done with a ROS, some of the smaller bits you might be better with a rectangular orbit sander either a 1/3 sheet or detail sander. Between the slats will sand pretty quickly with some strips/sheets of paper held between your hands.

One point to add is if you're not doing it already I would recommend wearing a dust mask etc while doing this iirc teak is particularly good at irritating your lungs plus you don't know what chemicals were in previous treatments that you're sanding off.

No that I see the pictures. Maybe all you need to do is hit it again with the power washer. It's really not that bad. You may have to add a littler color to help even things out with a good water base deck stain. Treat it like an outdoor deck. Sometimes we have to play the cards as given.

 

-Ace-

I've used Te-Ka two-part teak cleaner to spiff up teak decks. It gets rid of a lot of sins including engine grease or oil stains and leaves a bright, newly-cut look to teak. However, it's extremely acidic and with multiple applications over time it eats away the softer fast-growth rings, leaving the slow-growth rings as "ridges" in the surface.

It says it's brushless but if you use it I'd recommend using a medium-bristle brush anyway, because you're working on various vertical surfaces and want to get the Te-Ka onto everything. Wear heavy rubber gloves. If it can dissolve wood, it can dissolve you. :)

It doesn't look too bad, try washing it again and getting into stubborn spots and corners with a  card scraper. 

  • Author
5 hours ago, AceHoleInOne said:

No that I see the pictures. Maybe all you need to do is hit it again with the power washer. It's really not that bad. You may have to add a littler color to help even things out with a good water base deck stain. Treat it like an outdoor deck. Sometimes we have to play the cards as given.

 

-Ace-

Thanks, Ace! Is there any reason why you say water based stain?  That's my main concern with staining - choosing the wrong one (since it seems nothing is made for this kind of wood) and having it not take, or flake off. 

2 hours ago, ClassAct said:

I've used Te-Ka two-part teak cleaner to spiff up teak decks. It gets rid of a lot of sins including engine grease or oil stains and leaves a bright, newly-cut look to teak. However, it's extremely acidic and with multiple applications over time it eats away the softer fast-growth rings, leaving the slow-growth rings as "ridges" in the surface.

It says it's brushless but if you use it I'd recommend using a medium-bristle brush anyway, because you're working on various vertical surfaces and want to get the Te-Ka onto everything. Wear heavy rubber gloves. If it can dissolve wood, it can dissolve you. :)

This might be the answer! I'm reading reviews on Amazon and it looks promising. Thank you! 

I've never seen a water based deck stain that didn't form a film that started to peel after a couple of years. The oil based deck stains are much easier to maintain. 

Have they improved that much in the last couple of years?

Reason for water-based - oil takes so dang long to dry and stinks. Yeah the water-based can peel on ya. But my hope is you could bring the chairs inside for the winter. So they peel in 3 to 5 years??? ...you hit them again with the power washer, bleach and re-coat. It's outdoor wood ~ yep no magic bullet requires maintenance - oil or water-based.

 

-Ace- 

  • Author
58 minutes ago, AceHoleInOne said:

Reason for water-based - oil takes so dang long to dry and stinks. Yeah the water-based can peel on ya. But my hope is you could bring the chairs inside for the winter. So they peel in 3 to 5 years??? ...you hit them again with the power washer, bleach and re-coat. It's outdoor wood ~ yep no magic bullet requires maintenance - oil or water-based.

 

-Ace- 

Well, they will be on a covered porch and I'm in Tennessee, so the "winter" isn't much of one anyway. So at least that works in my favor! 

Well, they will be on a covered porch and I'm in Tennessee, so the "winter" isn't much of one anyway. So at least that works in my favor! 

 

Aren't they supposed to just be teak oiled every year?

 

 

Sent from my iPhone using Tapatalk

On 3/21/2017 at 7:45 PM, NashvilleDIYer said:

Well, they will be on a covered porch and I'm in Tennessee, so the "winter" isn't much of one anyway. So at least that works in my favor! 

Osmo deck oils (or some of their other stuff) would probably do the job for you - dries in 12 hours (or faster) and low odour. http://www.osmona.com/

  • Author
  • Popular Post

I so appreciate all of your input!! I decided to go with a walnut color Danish oil. The first photo is one coat (table) and the second (of one chair) is two coats. (One of my diy christmas decorations saying hello!) I can still see some of the old finish but it's much more difficult to see now. I'll do three coats on the main surfaces, sew some cushions, and call it a day!! Thanks again! 

20170325_142117.jpg

20170325_142101.jpg

Their looking nice. That color is gonna look nice and deep with all the coats on it.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,012 Total Members
  • 3,644 Most Online
  • JAR Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.