Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Applying ARS

Featured Replies

Nearing the point of starting final finish on a white oak piece.  Is this a good video to follow for applying ARS? A couple of things surprised me a little that he describes.  He talks about coming back 4-2 hours for follow up finishes when the can says 12-24.  He also uses mineral spirits between coats, I had thought it's only safe to use that prior to the first?  Finally, I had been planning to run fans on the piece from the time i start clearing off the dust to the time the final coat is finished.  My thinking is that this will keep dust from landing on it as the finishing area is in a garage that has people coming in and out of it.  Smart idea or not?

 

 

Matt Cremona knows his stuff so I would have nothing bad to say about his technique/process. I have used ARS on multiple projects now and it's pretty foolproof. I didn't use mineral spirits in-between coats but rather just lightly sanded the first coat with 320 and then each subsequent coat was rubbed down with #0000 steel wool before a new coat was applied. 

As for the fan thing, it sounds like a good idea in theory... but it could just as easily blow dust on the project as it could blow dust away so YMMV.

Drying time is hugely variable, dependent on temperature, humidity & air movement. I find I can usually recoat in about 4 hours.

I always use a fan, but not until the finish has dried to the point where it is no longer tacky. Seems like the fan tends to stir up dust.

  • Popular Post

My protocol for ARS is a little different than Cremona's.  I wrote up my entire process somewhere on this forum a couple times, but I can't find the posts.  If you search for it you might find it.  If I find the energy later I'll post it again.

Edit: Here's a copy I wrote for another forum member in a PM a while back...

 

I thin my ARS with mineral spirits, and the whole process usually goes like this (slight variations depending on the specific project, how much abuse it will take, what species of wood I'm using, but this is the general outline):

1) First coat, full strength...no thinning.  I put the first coat on pretty heavy and let the wood drink up all it wants.  Make sure to wipe up any pools, drips, runs before you take your gloves off.  These are a PITA later if you miss them, as I'm sure you're already aware.  Vigilance pays off here.

2) Let dry 8 hours or more, then sand lightly with 320.  If I missed any drips, I'll use the card scraper to gently remove them...be careful not to go back to raw wood...you just want to level it off.  I find if you try to sand a drip, you end up getting back to raw wood before the drip is gone, and you don't want that.  Card scraper works better but it takes a light touch.  I'll use the ROS with 320 grit to sand large panels...don't sit in one spot too long...one or two passes does the trick...you're just removing dust nibs and a tiny bit of raised grain.

3) Second coat, full strength, but I don't apply this coat as heavily.  Just a nice even coat.

4) Let dry and sand lightly with 500 (I'll use the ROS with a 500 grit Platin pad on larger panels at this step.)  If you only have wet/dry paper at these higher grits, 600 is okay, too.

5) Third coat I dilute about 3:1 ARS to mineral spirits.

Sometimes that will be my last coat if I'm doing a piece that doesn't require too much protection and I'm happy with the film I've built and the appearance of the finish.  If I'm doing something that requires significantly more protection, I will repeat steps 3 and 4 before I move on to step 5.

6) Optional fourth coat, diluted 1:1 ARS to mineral spirits.  This very diluted solution will flow and level very nicely, will help avoid the streaking that is common with wiping varnish, and will dry much faster which helps avoid dust nibs settling in your final coat.

7) Allow to cure, at least 24 hours but 48 or more is better.

8) Polish finish with 1000 grit Platin pad (for satin finishes), wet sanded with a mixture of 3:1 mineral spirits to mineral oil.  I do this by hand (with the grain) on oddball parts, but I'll use the ROS for larger panels.

9) Wipe dry with clean terry cloth rags or t-shirts.  If you find the surface is still too oily, you can wipe it again using straight mineral spirits to remove the oil.

10) Take project inside and stink up the house. :D

7 minutes ago, DailyGrind said:

How would you apply on vertical surfaces?

I do it the same as for horizontal. The coats go on so thin that running has never been a problem for me.

I use to use a foam brush to apply the ARS and used a raking light to locate the constant runs. In a pm from Eric, he sent me the same prescription as he posted above. I haven't used a foam brush since, but still use the light, just in case. 

10 hours ago, Eric. said:

My protocol for ARS is a little different than Cremona's.  I wrote up my entire process somewhere on this forum a couple times, but I can't find the posts.  If you search for it you might find it.  If I find the energy later I'll post it again.

Edit: Here's a copy I wrote for another forum member in a PM a while back...

 

I thin my ARS with mineral spirits, and the whole process usually goes like this (slight variations depending on the specific project, how much abuse it will take, what species of wood I'm using, but this is the general outline):

1) First coat, full strength...no thinning.  I put the first coat on pretty heavy and let the wood drink up all it wants.  Make sure to wipe up any pools, drips, runs before you take your gloves off.  These are a PITA later if you miss them, as I'm sure you're already aware.  Vigilance pays off here.

2) Let dry 8 hours or more, then sand lightly with 320.  If I missed any drips, I'll use the card scraper to gently remove them...be careful not to go back to raw wood...you just want to level it off.  I find if you try to sand a drip, you end up getting back to raw wood before the drip is gone, and you don't want that.  Card scraper works better but it takes a light touch.  I'll use the ROS with 320 grit to sand large panels...don't sit in one spot too long...one or two passes does the trick...you're just removing dust nibs and a tiny bit of raised grain.

3) Second coat, full strength, but I don't apply this coat as heavily.  Just a nice even coat.

4) Let dry and sand lightly with 500 (I'll use the ROS with a 500 grit Platin pad on larger panels at this step.)  If you only have wet/dry paper at these higher grits, 600 is okay, too.

5) Third coat I dilute about 3:1 ARS to mineral spirits.

Sometimes that will be my last coat if I'm doing a piece that doesn't require too much protection and I'm happy with the film I've built and the appearance of the finish.  If I'm doing something that requires significantly more protection, I will repeat steps 3 and 4 before I move on to step 5.

6) Optional fourth coat, diluted 1:1 ARS to mineral spirits.  This very diluted solution will flow and level very nicely, will help avoid the streaking that is common with wiping varnish, and will dry much faster which helps avoid dust nibs settling in your final coat.

7) Allow to cure, at least 24 hours but 48 or more is better.

8) Polish finish with 1000 grit Platin pad (for satin finishes), wet sanded with a mixture of 3:1 mineral spirits to mineral oil.  I do this by hand (with the grain) on oddball parts, but I'll use the ROS for larger panels.

9) Wipe dry with clean terry cloth rags or t-shirts.  If you find the surface is still too oily, you can wipe it again using straight mineral spirits to remove the oil.

10) Take project inside and stink up the house. :D

Probably about time to make this one a sticky thread.

 

The method I use is a hybrid of what Cremona and Eric do. It has evolved for me through experimentation.

 

 

Steps:

 

1. Full strength coat.

 

 

2. Lighter full strength coat.

 

 

3. Sand with 400 lightly.

 

 

4. 1:1 coat

 

 

5. 1:1 coat

 

 

6. Sand with 600

 

 

7. 1:1 coat followed by 0000 steel wool.

 

 

 

Mineral spirits wipe after each sanding along the way.

 

 

 

My biggest issue is my ADD/ADHD making me want to rush so I can get onto the next thing I want to do. Playing soothing R&B music in the shop helps me slow down.

 

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.