Mark J Posted February 25, 2025 Report Posted February 25, 2025 I've had this Rigid oscillating spindle & belt sander for several years, but this is the first time I've ever attempted to set it up in spindle mode. CS is closed for the day. I'll try them tomorrow, but maybe someone here knows the secret. The sanding sleeve is loose on the rubber drum, such that it's never going to oscillate, and probably won't spin much, either. These are the original drums and sleeves and I followed the installation directions in the manual (I believe). I know sometimes with a rubber drum you're supposed to tighten down to force the cylinder into a barrel shape, but that would take a heck of a lot of "tightening" with these drums. And the directions explicitly say not to over tighten. Am I missing something, or is there some work around? Anybody else had this problem? Quote
fcschoenthal Posted February 25, 2025 Report Posted February 25, 2025 Mark, have to ask, do you have the washer on top of the spindle? When the nut tightens, it compresses the spindle and bows it outward to hold the sleeve. That's the only thing I can think of right now. 1 1 Quote
gee-dub Posted February 25, 2025 Report Posted February 25, 2025 @fcschoenthal - is on target. there are a variety of washer sizes. the washer in use needs to be slightly smaller than the drum to assure it does not press directly against the abrasive sleeve. It needs to compress the rubber drum and expand it against the sleeve. One exception may be the 1/4" sleeve. I believe it is retained by a metal clip at the base of the shaft. 1 1 Quote
Mark J Posted February 26, 2025 Author Report Posted February 26, 2025 Yes I have the top washer in place. I'm using the second largest drum (1 1/2"?). According to the instructions that uses the 7/8" washer. I cranked down pretty hard on the threaded knob, enough that I was concerned. I can examine the setup again, in light of your comments. I might also try wrapping some painter's tape on th drum. Quote
Mark J Posted February 26, 2025 Author Report Posted February 26, 2025 OK! You guys are right. You have to tighten the knob quite a bit. Thanks! 1 Quote
Beechwood Chip Posted February 26, 2025 Report Posted February 26, 2025 Sometimes the spindle would slip, and sometimes it wouldn't. I might be imagining this, but when the sleeve is slipping, I found that flipping the rubber drum over (top to bottom) would help. 1 Quote
wtnhighlander Posted February 26, 2025 Report Posted February 26, 2025 My biggest beef with the Rigid sander is that the knob requires so much force to squish out the rubber spindle, I need tools to break it loose again. If I used the spindles more, I'd be looking for a replacement nut to embed into a big, honkin' knob. Or a wrench. Quote
fcschoenthal Posted February 26, 2025 Report Posted February 26, 2025 On 2/25/2025 at 10:05 PM, wtnhighlander said: If I used the spindles more, I'd be looking for a replacement nut to embed into a big, honkin' knob. Or a wrench. There was a whole conversation on finding a 3D printed wrench to fit the Ridgid sander. I printed my own, but several bought ones off of Etsy. 2 Quote
Mark J Posted February 26, 2025 Author Report Posted February 26, 2025 Yeah, I got a wrench off eBay. Inexpensive and works well. 1 Quote
Mark J Posted February 26, 2025 Author Report Posted February 26, 2025 Here's the thread. https://www.woodtalkonline.com/topic/35508-help-with-rigid-oscillating-belt-sander/ 1 1 Quote
Popular Post krtwood Posted February 26, 2025 Popular Post Report Posted February 26, 2025 Sometimes I end up putting some tape or self adhesive shipping label on the rubber drum just to make it a little bigger so I don't have to overtighten a loose sleeve. There is some variability in the sleeves and the drums might shrink a little with age and temperature probably comes into it both in terms of size and flexibility. 4 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.