Popular Post Chet Posted March 27, 2025 Popular Post Report Posted March 27, 2025 I have been working on a prototype for a project I have planned. But this all depends on how the prototype comes out. One of the features is bow front drawers. So while I was cutting laminates for the drawer front test, going back and forth between the band saw and jointer, I turn on the jointer one time only to get a loud ear splitting squeal. I shut it off while thinking I have a bad bearing in the cutter head. This would really upset me as the cutter head is only somewhere around 18 months old. I unplugged the machine and pulled the pork chop out of the way and rocked the cutter head back and forth and there wasn't and resistanance that would indicate a bad bearing. So I did the only smart thing and plugged the machine back in and turned it on again. Same squeal but it stopped in about two second and what I then heard was something that sounded like a 10 HP 3 Phase Motor running up to speed in some old factory. I turned everything off and disconnected the power and dust collection. Then I opened up the back side of the jointer and found that I had lost the key in the keyway on the top pulley, along with one of the two set screws in the pulley. Replaced them and all is right with the world once again. The one puzzling thing is that even with ear protecting on you would think you would hear any metallic parts being tossed around in side the base cabinet. 5 Quote
fcschoenthal Posted March 27, 2025 Report Posted March 27, 2025 Glad it was a fairly quick and inexpensive fix. My experience is that it never turns out that way. 2 Quote
Chet Posted March 27, 2025 Author Report Posted March 27, 2025 On 3/27/2025 at 11:39 AM, fcschoenthal said: Glad it was a fairly quick and inexpensive fix. My experience is that it never turns out that way. Yes, my first knee jerk, pit in my stomach reaction was fill with $$$. 1 Quote
Ron Swanson Jr. Posted March 27, 2025 Report Posted March 27, 2025 It's probably under, around or in the machine somewhere. My last jointer, a Delta, was famous for that trick. 2 Quote
Chestnut Posted March 28, 2025 Report Posted March 28, 2025 I had the same thing happen to my jointer. I knew something was coming though because every time i turned it on I'd hear a loud clang. After i heard that motor spinning up like you described I found the key and set screw and figured out what the clang was. 2 Quote
Chet Posted March 28, 2025 Author Report Posted March 28, 2025 On 3/27/2025 at 2:55 PM, Ron Swanson Jr. said: It's probably under, around or in the machine somewhere. I looked around pretty good and the shops pretty clean but it has to be out there somewhere. 1 Quote
Popular Post Coop Posted March 28, 2025 Popular Post Report Posted March 28, 2025 On 3/27/2025 at 9:08 PM, Chet said: I looked around pretty good and the shops pretty clean but it has to be out there somewhere. It could be a 4x4x12 and get lost in my shop! 1 4 Quote
curlyoak Posted March 28, 2025 Report Posted March 28, 2025 Me too. I have an old 6" delta jointer. The key loosened and cut a hole about 1" in the side. The cabinet has sheet metal and the key cut the hole. It seems to re occur occasionally. But it has been a long time since the last issue. A friend has a delta bandsaw that had the same issue. A hole in the sheet metal panel. 1 Quote
Popular Post Chet Posted March 28, 2025 Author Popular Post Report Posted March 28, 2025 On 3/28/2025 at 7:21 AM, Mark J said: Look in the dust collector bin. Its not that important that I find it. 4 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.