Popular Post Beechwood Chip Posted October 26 Popular Post Report Posted October 26 My current assembly table is a 72" x 36" butcher block top, 1 3/4" thick, mounted on a metal base. I got it for free. The size is good for my shop and it works well enough. I store my dust extractor under it, which is convenient when I'm using hand held tools with dust ports. And I can sit at it when using my laptop or doing fine work. There are two things that made me want to replace it: The sheet metal aprons make it difficult to clamp things to the edge. I cut MatchFit slots into the top. I have the first version of the Triton TRC001 router, and the collet slips every time I use it. This was the first time I used it, and the MatchFit slots were all wonky. Once I noticed I stopped. At the time I figured I was doing something wrong. So, I have a a few MatchFit slots that mostly work, but piss me off every time I look at them. So, my goals for the new table are: Clean MatchFit slots over half or all of the table Sit at table like a desk Space under table for dust extractor Able to clamp to table around all edges Thick table top for mass and esthetics Low cost Fun project Simple construction that I'm comfortable and confident with I've been thinking about this project for a few months, coming up with a design, and then tweaking it, modifying it, then throwing it out and starting over. Rinse, lather, repeat. One version had six legs. I think I finally have a design I'm happy with. I'm basing it on the Minimum Timber Bench by Rex Krueger. I got rid of the tool well, and I got rid of the front stretcher so I could sit at it. I reduced the front apron to make it easier to sit at and to make a uniform clamping situation all around. Instead of beefy 2x diagonals above the stretchers, I decided to mortise in 8" wide plywood stretchers on the sides and back. My current metal base doesn't have any stretchers, so I figure the 8" plywood should be enough to prevent racking and keep it rigid. In the front where there's no stretcher, I added a couple of small diagonals. I figure they'll be small enough that they won't interfere with the dust extractor or my knees. Once I had a design that I was comfortable with, I dove into Sketchup and did a rough drawing. I think this has everything except the fasteners. 3 Quote
Popular Post Beechwood Chip Posted October 26 Author Popular Post Report Posted October 26 A few things aren't obvious from the sketches. I'll probably use screws and dowels for the joints, but I may change my mind as things come together. Everything except the plywood is going to be 8/4 stock, whatever thickness it ends up after milling. The top will be a glue-up panel. I'll use a router to make slots in the bearers (cross pieces, joists), and screw the top down from below. The slots will allow for wood movement. 4 Quote
Popular Post wtnhighlander Posted October 26 Popular Post Report Posted October 26 Given this is an assembly table, not subject to the same forces applied to a hand-tool workbench, I'm thinking those front corner braces aren't really needed for strength. If they interfere with your planned use, I'd say you could eliminate them. 3 Quote
Von Posted October 26 Report Posted October 26 Good looking design. No obvious flaws I can see given your criteria. I will +1 to @wtnhighlander - I would try omitting the the corner braces as I don't think you'll need them and hey could get in the way of some clamping scenarios. I think you could reasonably add them later if the Internet/us lead you wrong. Given you have some experience already with Matchfit and table tops: how do you manage dust collecting in the grooves? Even on my smaller surfaces (I have a groove in my miter saw table for a stop), I'm finding it's a pain to keep them dust free enough so they work well. Maybe this just isn't an issue with an assembly table? 1 Quote
Mark J Posted October 26 Report Posted October 26 What about just using a vacuum on the grooves? Quote
Beechwood Chip Posted October 26 Author Report Posted October 26 On 10/26/2026 at 8:34 AM, Von said: how do you manage dust collecting in the grooves? The dust extractor takes care of that. For a long time I couldn't see the value in spending hundreds of dollars for a glorified shop vac, but the Hercules dust extractor is reasonably priced, and it really is much more effective than a shop vac at many tasks. Cleaning up the MatchFit grooves is one of those. 2 Quote
Popular Post Beechwood Chip Posted October 26 Author Popular Post Report Posted October 26 Good idea about the corner braces, it would be easy to add them later if needed. I'm calling this an assembly table, but I don't have a workbench so this is a compromise design. I don't do much hand tool work, and so far my metal based table has been good enough for the hand tool work I do. 3 Quote
Popular Post Tom King Posted October 26 Popular Post Report Posted October 26 I have used a solid core door for as long as I can remember. It's on some fairly fancy orange cast iron base that I found at a recycling place, but I can't find a overall picture of the base right off. Over a few decades, it has developed a sag in the middle. I clamp things to it sometimes and it does have a bench vise. 6 Quote
Popular Post Beechwood Chip Posted October 26 Author Popular Post Report Posted October 26 My computer table desk is a hollow core door. Used to be on sawhorses but I eventually knocked together some cabinets. 4 Quote
Popular Post Beechwood Chip Posted October 27 Author Popular Post Report Posted October 27 Once I had a design I was happy with, I created a spreadsheet to figure how much lumber I needed. I planned to use red oak for the top and poplar for the base to save money. Poplar was the least expensive wood I could find in 8/4, but I figured it would be too soft for the top. Red oak was the least expensive wood I could find that was hard enough. I decided to get 30% extra to be on the safe side. I plugged in the prices from the Hearne Hardwoods website, since they are about an hour away and I've used them before. Then I pulled out a list I had made a while back of every local hardwood dealer, and every mail order place that anyone had recommended. 22 businesses altogether. I hit all of their websites and compared prices in another spreadsheet. Of the first 21, there were only five that were in the ballpark. Two were slightly cheaper for "Select & Better", but Hearne sold FAS. Then the last one on the list was AMC Hardwoods, and they offered 100 BF of 8/4 FAS Red Oak, 6 to 8 feet long, random widths, for $520. And, they are only 20 miles away! From their website, During normal operations a small percentage of material is pulled from wholesale orders for various reasons, such as not meeting required dimensions. We gather this material and instead of spending the time processing it back into warehouse inventory, It goes to the outlet store and gets sold to the public with no minimum purchase! Sounds perfect for my project! I'm just checking with them that "random widths" means 4 to 10 inches, and then I'll drive out there and fill the Subaru with wood. BTW, if anyone wants the SketchUp drawing or my Google Sheets spreadsheet, just ask. Nothing amazing, but it does contain things like =SUMIF($H$2:$H$7, CONCATENATE("=", $B9), $F$2:$F$7) 2 1 Quote
Popular Post gee-dub Posted October 27 Popular Post Report Posted October 27 I have found poplar to be a great structural material. My current workbench base is poplar, my sideboard back panel frame is poplar. The yellow green color often puts people off but I can attest that it does age to a nice light chocolate brown. If I am doing something that requires a heavy duty-cycle like dust panel drawer dividers that drawers actually slide on I will use maple but poplar has served me very well for years of use in non-direct contact areas. Glued up 1/2" drawer bottoms is another area where poplar excels at a reduced cost from maple. 4 Quote
Popular Post Mark J Posted October 27 Popular Post Report Posted October 27 11 hours ago, Beechwood Chip said: Nothing amazing, but it does contain things like =SUMIF($H$2:$H$7, CONCATENATE("=", $B9), $F$2:$F$7) This made me chuckle . 4 Quote
Von Posted October 27 Report Posted October 27 11 hours ago, Beechwood Chip said: =SUMIF($H$2:$H$7, CONCATENATE("=", $B9), $F$2:$F$7) Spreadsheets are self-contained programs and data combined into one. The things I've seen scientists do with them... 2 Quote
gee-dub Posted October 27 Report Posted October 27 Shades of Lotus 1-2-3 I used to use spreadsheets to do nationwide network designs before we had ethernet over fiber, before we had ATM, things got so much easier as technology advanced. 2 Quote
Von Posted October 27 Report Posted October 27 1 hour ago, gee-dub said: Shades of Lotus 1-2-3 I used to use spreadsheets to do nationwide network designs before we had ethernet over fiber, before we had ATM, things got so much easier as technology advanced. I feel the pull of a walk down IT memory lane and will resist. There are several of us on this forum who have had that career and I suspect could spend a enjoyable time swapping stories, especially over beverages. 2 Quote
wtnhighlander Posted October 27 Report Posted October 27 8 hours ago, Von said: I feel the pull of a walk down IT memory lane and will resist. There are several of us on this forum who have had that career and I suspect could spend a enjoyable time swapping stories, especially over beverages. Ha! I'll start ... have you ever had to diagnose a memory failure by counting beads in the 'core'? 1 Quote
Beechwood Chip Posted October 31 Author Report Posted October 31 I'm planning to pick up the lumber Wednesday. The boards are going to be 6 to 8 feet long, my Outback can fit 6 and a half feet with the rear seats down, and the roof rack can only hold 150 lbs. I plan to bring a cordless circular saw and do wood butchery in the parking lot as needed. I'll have a friend, and I figured that I'd stick the board in the car hanging out the back, my friend will hold the loose end, and I'll make the cut. I'm a little leery, because I've never been to this lumber yard before and I don't know what to expect. Any advice or cautions would be appreciated. 1 Quote
Von Posted October 31 Report Posted October 31 You might see if they will deliver. I have a local lumber yard that delivers for a reasonable fee ($50?). I usually try hard to borrow a truck or a friend with a truck. If that isn't an option, I think you can do hourly rentals reasonably. I've seen contractors doing all sorts of odd jobs (e.g. brazing) in the parking lots so I wouldn't think you'd have any issue with the store. If they aren't used to contractors, then they will certainly be use to us hobbyists without trucks. You doing rip cuts or just cross cuts? For cross cuts, I find a jig saw a little more manageable in such situations but that could just be me. And I don't have a cordless circular saw :-) You probably have too much lumber for this to be useful, but I find I can get a 8' board or two in the car if I go between the front seats. 1 Quote
Beechwood Chip Posted October 31 Author Report Posted October 31 Shipping doesn't seem to be available, at least according to their website. Maybe because this is outlet lumber and they don't want to bother. I'm getting it at $5.20 and other yards would charge $6. I strongly considered renting a truck or a trailer. Maybe I'm being silly, but I decided that if I could cram it into my car, that's what I preferred. Perhaps this will be a learning opportunity, and next time I'll rent. I'm doing cross cuts. I have a cordless circular saw, but my jig saw has a tail. I don't know how many long boards there will be. I may be able to squeeze them all in with no cutting. All good suggestions, thanks! 1 Quote
Popular Post wtnhighlander Posted October 31 Popular Post Report Posted October 31 Remember to take a speed square to guide your saw! Trust me, keeping these cuts square can mean the difference between a stick that is just long enough for a 3' part, or a 35" scrap. 4 Quote
Popular Post Beechwood Chip Posted November 1 Author Popular Post Report Posted November 1 Good point. I plan to cut everything 2" oversize to allow for precise cuts later. But I'll definitely bring a square! Thanks! Oh, and I might as well bring a quick-clamp as a 3rd (5th?) hand. Better to have it and not need it ... 3 Quote
Popular Post Mark J Posted November 1 Popular Post Report Posted November 1 16 hours ago, Beechwood Chip said: I have a cordless circular saw, but my jig saw has a tail. Silly question, but does the circular saw have enough cut depth for the boards you will buy? (Safety glasses?) In addition to the square, a marking pencil. More than one quick clamp. Rope and bungees in case you can't close the hatch, or something winds up on the roof. 3 Quote
Popular Post Beechwood Chip Posted November 1 Author Popular Post Report Posted November 1 I just thought of that! Checked the depth of cut, 2 1/2" should be enough for 8/4. Here's my current check list: carpenters pencil safety glasses hearing protection speed square Quick clamps Gloves (splinters!) Circ saw, batteries Tie downs Tape measure Red Flag (in case something sticks out the back) Water Bottle 3 Quote
Popular Post curlyoak Posted November 1 Popular Post Report Posted November 1 Poplar is a very good choice for building benches. My preference is 2 x 6 construction grade spruce. It comes reasonably clean of knots and is extra strong. I have made all my benches with 2x spruce. and I Used some 1x poplar. 3 Quote
Popular Post Von Posted November 1 Popular Post Report Posted November 1 Some old towels or moving blankets if you think you might want to protect the back of your front seats or other parts of the interior. 3 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.