Recommended Posts

Posted

I have a Dewalt 735 planer. I am doing some box work and sometimes, I would like to be able to plane a 6", 8", or 10" long board from 3/4 thick down to 1/2". Can shorter boards be planed? Does anyone know the minimum length board the 735 will plane? I figure I'd ask all of you instead of searching the manual. I have some ideas on how but what have you successfully done?

Thanks

Tim

Posted

once boards get that short, i pull out a #5. Maybe there's a technique for the 735, but 6" is quite short. What I would worry about is the stability of very short stock under the head -- if it lifts & shatters, you've got a problem ... Not sure what the spacing of the rollers/head is on these small units. I usually stop at 16"...

Sometimes I feed shorter stock end-to-end (like a flat wooden train) to minimize snipe, but nothing like 6". Maybe others can provide specific info for benchtop units.

Not sure if you are working from scrap, but, it's better the plane for thickness prior to cross-cutting to length to avoid such issues. also, don't even think of running 6" stock over the jointer... don't even try to find a clever way to do something like that...

  • Like 1
Posted

I believe the manual states 12" but if you have it (the manual) you should read it just so you are more familiar with it.

It should be possible to make a carrier for it. I also recall an article where the person glued together smaller pieces to make a longer piece which could then be planed and ripped/cut back down to size. Should be able to Google it.

Posted

If it were really super or rare wood, I'd do this with a hand plane or some sort of carrier. My DeWalt planer states a minimum length of 12". I happen to own a drum sander, and while it's not dangerous, results can get pretty wonky as boards get shorter than 8"

In cases of common woods, I'd use most pieces that size for jigs, hidden parts, like corner blocks, or to fire up my deck firebowl.

As mentioned earlier, power jointing boards this short is asking for an accident, and likely to result in less than stellar results anyway.

  • Like 1
Posted

ok before you use a hand plane or do a complecated glue up. break out your hot glue gun and a couple of 2 foot rips. glue your long pices to the sides of your short piece and then you can put it through the planer. you can do the same thing to make it thiner then what the max is on planer. just hot glue your wood to piece of scrap wood and then put it throught the planer.

the long pieces stabablize it and give you a handle.

  • 2 years later...
Posted

duckkisser - just last night I did what you suggested and it worked great. The problem was that the hot glue was WAY stronger than I anticipated and I couldn't snap the workpiece off from the carriers that I had glued it to! I even tried splitting it with a chisel but it wouldn't give. I decided to run it through the table saw to cut off the edge of the carriers closest to the workpiece, and it did work, but it got hot glue ALL OVER my blade. I take it that was not the way that the pieces are supposed to be separated? How do you usually separate the workpiece once you've planed it with the carriers? (and any ideas for getting hot glue off blade teeth?)

 

Thanks,

David

Posted

Put the blade in the freezer for a few minutes, then it should chip off. I use sample laminate chips to scrape off hot melt.

You can glue the strips on w yellow glue, just put a single sheet of newspaper/notebook paper in the joint .

After planing you can split the joint with a chisel. The paper becomes a fault line. If you use Titebond wait at least 2 - 3 hrs and it should be strong enough to plane .

  • Like 1
Posted

Put the blade in the freezer for a few minutes, then it should chip off. I use sample laminate chips to scrape off hot melt.

You can glue the strips on w yellow glue, just put a single sheet of newspaper/notebook paper in the joint .

After planing you can split the joint with a chisel. The paper becomes a fault line. If you use Titebond wait at least 2 - 3 hrs and it should be strong enough to plane .

That's a nugget Steve....thanks.

David, less hot glue? Spread it thinner and fewer spots. I know you see this but some of it is trial and error to know how much is enough.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Who's Online   0 Members, 0 Anonymous, 45 Guests (See full list)

    • There are no registered users currently online
  • Forum Statistics

    32.1k
    Total Topics
    437.6k
    Total Posts
  • Member Statistics

    26,008
    Total Members
    3,644
    Most Online
    Bob44
    Newest Member
    Bob44
    Joined