Recommended Posts

Posted

I am looking into reducing the size of my table saw fence from a 56" inch width fence to a 28" or 36" width fence.

If anyone knows a source for angle iron and the rectangular tubing that would be used with a Beissmeyer fence, please let me know.

Thank you,

Milo

Posted

I'm in Tallahassee, Fl.

I wonder what the "proper" name/description of the rectangular tubing is.

You both right. Stuff weighs a ton, and probably costs a mint to ship.

Posted

Aluminum is strong, but softer than the steel tubing of your original fence. You will probably need a thicker wall to avoid collapsing under clamp pressure. My saw has an aluminum fence rail, but it is round tube, harder to collapse than rectangular.

Posted

I found a guy a few years ago selling just the fence (no rails) for a Jet Exacta  fence...basically a biesemeyer.

 

I made the rail out of 2.5 x 2.5" angle iron, and a 2x3 tube.  The only difference between is the corners have a larger round over but it doesn't affect the functionality of the fence.  I got them at a metal recycler.  I bought enough for a 5 ft fence.  I think it was maybe $70.

Posted

I checked my local supplier metal supermarket and they are usually a little high. Your tube @ 30" is $20 the angle is $25 if its 3 x 3 less if smaller. Should be close all over the US. That's hot rolled structural tube and hot rolled structural angle. There may even be a metal supermarket in your city. They are big all over the US.

Posted

Exactly!   But you actually have to GO there...  ;)   Steel shapes are almost as easy to find in-person as sheets of OSB, and just as hard to find online.

 

It is a little cheaper that way. Metal Supermarkets ships from their closest location so the shipping is affordable. These two pieces would have been $48 online vs $29 local.

 

Posted

I wish we had Steel Supermarket in the area, but we do have plenty of one-off metal sellers.   None of 'em are online other than how to find them and business hours. 

 

Super easy to deal with in person, though.   Very helpful!  I've had experiences where a shop employee suggested a better, and/or cheaper, alternative than what I thought I wanted.

Posted

I have a number of fab shops around that would let me pay cash for off cuts. As long as you are willing to pay more than the recycler they will usually let small bits like this go cheaply.

Posted

Most cities have a metal scrap-recycling yard. Most of them also sell new steel of different sizes and shapes. If you don't mind getting dirty they will let you dig around and find some used stuff. You'll have to clean it up but you can save some cash.

Posted

IIRC correct, and I would have to go home, but I believe the bar on my Beismeire (sp) fence is machined.

 

I would expect that if you tried to use standard bar stock as a fence slide, the imperfections on a standard bar would get magnified over the length of the actual fence and be quite anoying.

 

I would either cut down the bar you have, or get the new ready made bar that has been machined flat, and has a nice powder coat finish on the non "bearing" surfaces.

 

But that's just me, YMMV.

  • Like 1
Posted

IIRC correct, and I would have to go home, but I believe the bar on my Beismeire (sp) fence is machined.

 

I would expect that if you tried to use standard bar stock as a fence slide, the imperfections on a standard bar would get magnified over the length of the actual fence and be quite anoying.

 

I would either cut down the bar you have, or get the new ready made bar that has been machined flat, and has a nice powder coat finish on the non "bearing" surfaces.

 

But that's just me, YMMV.

 

 

Its 2x3 1/8" wall hot rolled tube.

Posted

Its 2x3 1/8" wall hot rolled tube.

 

I was not saying it isn't 2x3 1/8" hot rolled tube. I am just saying it has machined faces where the fence slides on it.

 

And that machining may only be a few thousand's of an inch, but with out it, the natural variations of the stock will drive you batty when trying to align the fence. IMNSHO of course.

Posted

I was not saying it isn't 2x3 1/8" hot rolled tube. I am just saying it has machined faces where the fence slides on it.

 

And that machining may only be a few thousand's of an inch, but with out it, the natural variations of the stock will drive you batty when trying to align the fence. IMNSHO of course.

 

Probably be a good idea to check that. The piece I posted on page one is as flat as my jointer bed and extremely smooth, almost polished. I dont think there will be any issues unless the pieces were bent or dented.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Who's Online   2 Members, 0 Anonymous, 57 Guests (See full list)

  • Forum Statistics

    32.1k
    Total Topics
    437.6k
    Total Posts
  • Member Statistics

    26,009
    Total Members
    3,644
    Most Online
    Joseph b
    Newest Member
    Joseph b
    Joined