Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Roasting wood

Featured Replies

The first time I saw a piece of roasted maple it was on an Ernie Ball bass. It was fantastic! On a whim, I grabbed a piece of flame maple and propped it over my fire pit. The result was very encouraging. The figure darkened almost immediately, and the rest of the piece darkened nicely as well.

 

I'll post a picture tomorrow, but I wanted to see if any of you have tried something similar

 

 

I did that a few times on some BBQ builds.  Although, I used a torch, not the burn pit.. :)

I've toasted some hard maple with a large blow torch (used for shrink wrapping boats).  It took on a nice caramel color with a few passes.  When toasted a bit darker (not black, but ALMOST black) and went after it with some 320 grit to even out the color and lighten it up a bit, it looked great after an oil finish was applied :P .. 

 

Haven't tried it with other woods though...

The toasting method you are referring to, now common to some instrument makers, involves putting the wood in an oxygen free environment (usually using argon gas) and bringing the wood up to 400 degrees.  The lack of oxygen is key in that it stops the wood from burning, it roasts instead. 

  • Author

The toasting method you are referring to, now common to some instrument makers, involves putting the wood in an oxygen free environment (usually using argon gas) and bringing the wood up to 400 degrees.  The lack of oxygen is key in that it stops the wood from burning, it roasts instead. 

 

Thanks! Is there a good reliable source of roasted wood? I don't see a setup like that in the near future for me.

The toasting method you are referring to, now common to some instrument makers, involves putting the wood in an oxygen free environment (usually using argon gas) and bringing the wood up to 400 degrees.  The lack of oxygen is key in that it stops the wood from burning, it roasts instead. 

Interesting Jim. How deep does it go into the wood as I think the fire-pit method might only do the outer layers?.

If your toasting small pieces they can eanily be done in the kitchen on your stove. You can use a pan or baking sheet what ever works for you. Put plain old sand in the pan and warm the sand. Cover the bottom about 1/2".  Put the wood on the sand and toast to your desired crispiness. :)

If your toasting small pieces they can eanily be done in the kitchen on your stove. You can use a pan or baking sheet what ever works for you. Put plain old sand in the pan and warm the sand. Cover the bottom about 1/2".  Put the wood on the sand and toast to your desired crispiness. :)

 

Season to taste :)

Add a marshmallow and a chocolate bar and make "S'mores" to eat while you are thinking about the next project.  :P  ;)

 

Rog

  • Author

Add a marshmallow and a chocolate bar and make "S'mores" to eat while you are thinking about the next project. :P;)

Rog

We did that too :)

Posted Image

Sent from my iPhone using Tapatalk - now Free

I am not sure where you would get the wood.  The method would be difficult to do at home, because the key to the method is the oxygen free environment, otherwise the wood burns and you are just putting a finish on the wood.   Done properly, the roasting goes all the way through, drives out the moisture, and makes the wood extremely stable.  As I understand it, it is almost like the pores get cauterized and moisture will no longer go through the wood.

I am not sure where you would get the wood.  The method would be difficult to do at home, because the key to the method is the oxygen free environment, otherwise the wood burns and you are just putting a finish on the wood.   Done properly, the roasting goes all the way through, drives out the moisture, and makes the wood extremely stable.  As I understand it, it is almost like the pores get cauterized and moisture will no longer go through the wood.

 

Bury it in sand, perhaps?  Fill a metal box with play sand, bury the workpiece therein, then slide the whole thing into the oven and bake at 400 until, what?

  • Author

Bury it in sand, perhaps? Fill a metal box with play sand, bury the workpiece therein, then slide the whole thing into the oven and bake at 400 until, what?

If you can convince my wife that putting a box of sand in the oven is a good idea, I'll do it :)

How about this, I'll make a metal box, fill it with sand and some wood and put it in my fire.

Would this work?

If you can convince my wife that putting a box of sand in the oven is a good idea, I'll do it :)

How about this, I'll make a metal box, fill it with sand and some wood and put it in my fire.

Would this work?

 

Heat is heat so, in theory, sure.  But an oven would be easier to control the temperature.  How about a propane grill set on low?

  • Author

That could work. I'll try some things out. The problem is, I want really big roasted boards. I have some ideas... Maybe a similar thing to a steaming rig, but with a sealed metal box? 

If you can convince my wife that putting a box of sand in the oven is a good idea, I'll do it :)

How about this, I'll make a metal box, fill it with sand and some wood and put it in my fire.

Would this work?

 

I'm blessed in that my wife would support something like this.  She understands what the end result could be so, would be all in!

A large air tight container (with a pressure relief valve) that you can seal the wood in and then evacuate the oxygen by injecting argon gas.  Argon is denser than air, so if you have a vent on top, you can fill the container with argon and it will settle to the bottom and push the air out the top.  Remember you are heating this, so a pressure relief valve is needed (don't need anyone blowing up).  Filling a container with sand leaves a lot of room for air between the grains.

 

If I think about it, I am wondering if the container can just be open at the top, as the argon will "lay" in the bottom like water, being that it is heavier than air.  It would be safer with an open top as then you are not heating a sealed container and dealing with expanding gases.  Argon is inert, so not poisonous, but it will displace air, so be careful.

careful with inert gasses. while non-toxic, they are heavier than air, and you can get into trouble if you vent improperly.  your body will have trouble properly evacuating it from the lungs, or worse yet, should one of your household pets who is lower to the ground get into it, they can actually "drown" in the thicker air.

  • Author

careful with inert gasses. while non-toxic, they are heavier than air, and you can get into trouble if you vent improperly.  your body will have trouble properly evacuating it from the lungs, or worse yet, should one of your household pets who is lower to the ground get into it, they can actually "drown" in the thicker air.

 

That is a good point. I did not even consider this. 

careful with inert gasses. while non-toxic, they are heavier than air, and you can get into trouble if you vent improperly.  your body will have trouble properly evacuating it from the lungs, or worse yet, should one of your household pets who is lower to the ground get into it, they can actually "drown" in the thicker air.

 

This is a good safety moment! 

 

Not all "inert" gasses are heavier than air.  Argon I believe is but, Nitrogen is not.  If the goal is to simply displace the oxygen, Argon would not be my first choice.

 

There are a lot of youtube videos out there dealing with people (who usually die) and inert atmospheres.  In fact, the death rate is much higher than it should be because of the natural human factor of trying to save your buddy.

This is a good safety moment! 

 

Not all "inert" gasses are heavier than air.  Argon I believe is but, Nitrogen is not.  If the goal is to simply displace the oxygen, Argon would not be my first choice.

 

There are a lot of youtube videos out there dealing with people (who usually die) and inert atmospheres.  In fact, the death rate is much higher than it should be because of the natural human factor of trying to save your buddy.

This is true, not all inert gasses are heavier. Helium is a noble gas and it floats.  Lighter-than-air gasses are just as dangerous, if not more so, because they can block out oxygen from your bloodstream in a manner similar to carbon monoxide!

I would say the best idea is to leave it to the big boys that have specialized kilns.  While it is nice to know how it is done, this is one area where it is probably better to leave it to the pros.  Besides, after you get all set up to roast a few pieces of wood, it would b cheaper to just buy it.  Unless you are going into the wood roasting business of course.

It would seem to me that you could do this on a very small scale with an old self cleaning over. It would not be hard to add fitting and pull a vacuum. Do a search for lab ovens that is how they work and they are nothing special. My guess is you could do it with cast iron pipe. My question is why? From what I can tell it really makes the wood not good for much of anything except flooring. 

  • Author

My question is why? From what I can tell it really makes the wood not good for much of anything except flooring.

For guitar/bass necks. To be honest, I really love the look. If its more stable, then I guess that's just a bonus.

  • Author

Besides, after you get all set up to roast a few pieces of wood, it would b cheaper to just buy it.

I agree. If I can find a source I can trust, I'll be happy to buy some. The up charge for a bass neck is substantial. Usually around $350 per neck price increase. So, really if I can roast my own, for say $200-$500 I may be better doing it myself. I'm sure there is more to it than meets the eye, but I am interested!

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,011 Total Members
  • 3,644 Most Online
  • bobtjanitor Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.