Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Two Shellac Questions

Featured Replies

So, my favorite finish is shellac. There is no getting around that.

 

What would happen if I thinned the shellac down just a little bit? Would this make it easier or harder to apply? Also, when applying shellac, what is the easier applying method? Right now I am using just a cloth, but I am open to any other suggestions.

I have used the shellac in an aerosol can, and I found that quite easy to apply. Have you tried a spray system?

Thinner is easier to apply. That's pretty much the first step in French polishing and spraying shellac. Wiping or spraying on a 2lb or more cut will be very difficult.

I think'd spraying is the easiest, wiping second and brushing being the hardest.

  • Author

Are we talking spraying like hvlp/etc or aerosol cans?

I don't understand the fascination with shellac IMO modern finishes are easier to use and produce better results in less time.

 

 

It smells like vodka  

  • Author

I don't understand the fascination with shellac IMO modern finishes are easier to use and produce better results in less time.

Basically it's because I haven't strayed from my comfort zone yet. That's the honest truth.

I actually just used Amber Shellac for the first time. It was 3# cut, not thinned and padded on. Sanded after first coat, applied 4 more coats, rubbed it with Festool Platin S1000 abrasive pad, then went over it with mineral spirits and an Platin S2000 abrasive pad, wiped off excess MS. Not bad, very smooth finish. 

post-104-0-39257200-1385173734_thumb.jpg

I like the fast drying time of shellac. Also the lack of noxious fumes. I can apply 5 coats to a coffee table size piece in a single afternoon, and have it in the house by sundown. Last time I used poly, I brought the piece in after one coat and 8 hours of cure time, and still my wife and I had headaches all night from the smell.

So, my favorite finish is shellac. There is no getting around that.

 

What would happen if I thinned the shellac down just a little bit? Would this make it easier or harder to apply? Also, when applying shellac, what is the easier applying method? Right now I am using just a cloth, but I am open to any other suggestions.

Sam I forgot to mention that I "charged" my pad with denatured alcohol prior to dipping in the shellac, which probably gave me a little more time to spread the shellac. 

  • Author

Sam I forgot to mention that I "charged" my pad with denatured alcohol prior to dipping in the shellac, which probably gave me a little more time to spread the shellac.

That's an awesome idea.

It smells like vodka  

 

...It dilutes with vodka, too!

 

I don't understand the fascination with shellac IMO modern finishes are easier to use and produce better results in less time.

 

Which modern finishes would you mean?  For me, shellac has most of them beat in speed, cost, toxicity, odor and ease of clean-up.  Personally, I like the results better, too.  From what I've seen, even if you do include modern finishes in your work, shellac still has use as a binder, washcoat or sanding sealer.

 

As to the OP's question, thinner is easier and builds slower.  Different application methods:

  • An aerosol can:  Useful for very small projects.  Also useful any time your project includes an oily exotic (I'm looking at you, padauk) whose colors would run and smear with alcohol.
  • Spray gun:  Bigger projects that are already assembled
  • Brush:  Large surfaces (i.e. the 10' countertop at which I sit right now) where you want to lay down a lot to build a thick film and you know you'll be coming back to sand the surface level later.

Brushing shellac isn't necessarily hard.  Just be very aware of your strokes if your brushing final coats.  Earlier in the process, whether for barrier coats or sanding sealers that you know are going to get sanded later, brush away.  I keep a gallon of shellac at the bench and will frequently find reason to brush a coat on components during assembly or joinery.  Dries rocket fast and doesn't interrupt my workflow nearly as much as setting up for any of the more modern finishes.

In a commercial shop with a dedicated finishing room you just aren't noticing the drawbacks to "modern" finishes but for home shop use shellac is nice because it dries fast, melts into itself, is durable, comes in a variety of shades, can be stored dry, is compatible with pretty much every other finish, is extremely easy to repair, and doesn't stink up the shop/home with noxious fumes. Shellac can be mixed with oils and/or waxes to make friction polishes. It's not the perfect finish for every application or but it is an excellent finish.

Shellac is even used to coat food and medicine ! I would not use it for a final finish because a drinking glass will leave a ring and spilled alcohol will dissolve it.

But PB does have a point I use waterbourne sanding sealer and finishes that have less smell than shellac, aren't flammable and dry reasonably quick. I use shellac as a universal barrier coat between old finishes and waterbourne topcoats.

I just mentioned it as food for thought. I really don't see shellac as a finish or sealer but more of a problem solver. Its unnecessesary to use it as seen all to often as a universal sealant. As far as making repairs or some odd uses here and there its great to have in the shop but I do think it does get over used.

 

Here is a link to Flexner's article I tend to agree with his line of thinking. 

 

http://www.woodshopnews.com/columns-blogs/finishing/502292-shellac-as-a-sealer-its-all-just-hype

I just mentioned it as food for thought. I really don't see shellac as a finish or sealer but more of a problem solver. Its unnecessesary to use it as seen all to often as a universal sealant. As far as making repairs or some odd uses here and there its great to have in the shop but I do think it does get over used.

 

Here is a link to Flexner's article I tend to agree with his line of thinking. 

 

http://www.woodshopnews.com/columns-blogs/finishing/502292-shellac-as-a-sealer-its-all-just-hype

 

The best thing about this article is all the people asking for free advice in the comments section....  and the silence they are met with.  Someone should tell those people to come over here. 

I don't understand the fascination with shellac IMO modern finishes are easier to use and produce better results in less time.

I find it is simple to use, low cost, low waste, long shelf life when in flakes, and never have to worry too much about fumes or any allergic reaction.

It's funny...  In different situations, I can agree with every opposing viewpoint posted in this thread.

 

If pro shops used shellac as "the finish", it would be callback hell...  High performance, fast applying finishes were invented for real reasons, to fill actual market needs.  Nowadays, so many people clean with way too many chemicals, I can see shellac going downhill fast in a typical household.

 

However, I can see two situations where a pro shop might use shellac as "the finish".   First, and most obvious, is period reproduction work.  We wouldn't use an adjustable cup hinge here, nor a pre-cat clear finish...  Second, and maybe less obvious, is the pro catering to a certain hipster / organic craft / artisan customer.  Many of these folks don't want a high-performance, complex-chemistry, factory-quality finish, simply because it's a high-performance, complex chemistry, factory-quality finish.  Right or wrong in finish technicalities, there's a marketing angle here in favor of shellac.

 

For folks not working to a clock, and with some control over the end use of the item, shellac is a fast, easy to get, inexpensive, easy to use finish, with easy repairability, that doesn't require expensive equipment to apply, can be applied in a wide range of conditions, and doesn't create much in the ways of hazards or discomfort during application.  

 

I prefer to spray most of my furniture and all of my cabinetry with modern materials, but I still love to use shellac on small items like individual boxes.  I keep a bunch of rags in a jar, and a mixture of 1 lb. shellac on hand, and every few minutes, I wipe the box once, with a coat of shellac.  If you go back over the wet shellac, you rub off what you put on earlier, so it's once per coat.  Every 3-4 coats, I lightly sand it, progressively reaching 1000 grit wet/dry auto body paper, then finish with 0000 steel wool and wax.  I've never been able to duplicate the look and feel of this finish with anything else.  I just want to carry the box around, and offer to let strangers feel my wood.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,009 Total Members
  • 3,644 Most Online
  • Joseph b Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.