Llama Posted November 27, 2013 Report Posted November 27, 2013 Any reason to have two thickness planers? I have one, and just saw a good deal on another. Quote
Cochese Posted November 27, 2013 Report Posted November 27, 2013 If you have the room, only your budget would tell you no. As for a reason why? Unless one is a four poster and the other a portable... Sent from my HTC One using Tapatalk Quote
rodger. Posted November 28, 2013 Report Posted November 28, 2013 I also had the opportunity to buy a second planer at a good price, but couldn't think of a time when I needed two. The only thing I could come up with is if one was out of commission for some reason. Quote
Tom King Posted November 28, 2013 Report Posted November 28, 2013 One to take a lot of wood off of rough stuff, and another for more of a finishing planer. We also have a lunchbox one for when we need one not in the shop-of course, not everyone needs one of those if you have a stationary one. Actually, our second one I bought as a molder, and then found out it did a good job of running everything to exactly the same thickness-to the nearest thousandth. It's nice to have the big one that we don't worry about keeping the knives pristine in, since we have the second one for better finish. I guess the big planer could be called a Scrub Planer, and the second one a Smoothing Planer. 1 Quote
..Kev Posted November 28, 2013 Report Posted November 28, 2013 I honestly haven't come across a need for 2. However, if you have the room and budget, it could come in handy. If you need blades on the first one or it's out for repair, the back up could be used to keep you going. Quote
Llama Posted November 28, 2013 Author Report Posted November 28, 2013 It's probably overkill for me. Just thought I'd ask Now, if another bandsaw comes up for a good price, I'll be all over it! Quote
..Kev Posted November 28, 2013 Report Posted November 28, 2013 It's probably overkill for me. Just thought I'd ask Now, if another bandsaw comes up for a good price, I'll be all over it! 1 Quote
Llama Posted November 28, 2013 Author Report Posted November 28, 2013 I'm always looking for another! Or two more! Quote
rodger. Posted November 28, 2013 Report Posted November 28, 2013 Same with table saws. I would love to have two- one for rip and one for crosscut/joinery. Quote
TRBaker Posted November 28, 2013 Report Posted November 28, 2013 I like to plane both sides of faceplate material for cabinets, so I usually cut my material an 1/8" big and plane a 1/16th off of each side. If I had two planers, I'd set up one for the first cut and one for the second. Another scenario is keeping one set up at a critical thickness for the whole project and the second one for all the variations. 1 Quote
Tom King Posted November 28, 2013 Report Posted November 28, 2013 "Another scenario is keeping one set up at a critical thickness for the whole project and the second one for all the variations."I've done that, as well as two table saws dedicated for a project, and another for general use.The game "He Who Dies with the Most Tools" was called a long time ago on account of No Contest. Quote
wdwerker Posted November 28, 2013 Report Posted November 28, 2013 2 tablesaws is nice! I have a sliding table crosscut set up on one and a 12 ft outfeed table for ripping on the other one. I have an old lunchbox planer and a bigger planer that will also mold and rip. It's been nice to still be able to plane something when I have a molding head in the other machine ( because switching over does take about 45 minutes) Quote
wintersedge Posted November 28, 2013 Report Posted November 28, 2013 If you make your cash by woodworking I would buy a second one in a heartbeat. I have always found, no matter what field you work in, it is always nice to have a backup and in time you learn to optimize your workflow and increase production. If you have the space and cash I would jump on it.- disclaimer: this advice does not apply to having two wives. 1 Quote
Freddie Posted November 28, 2013 Report Posted November 28, 2013 Two table saws back to back would be really nice if space allowed it. Same with two bandsaws. I don't use a combo blade on my ts, I have dedicated rip and crosscut blades, I just prefer the better cut for each type. It tends to be a pain in the butt at times when a project requires a blade change, but I'm living with it. Quote
Eric. Posted November 28, 2013 Report Posted November 28, 2013 I like Tom's thought of having a beater for rough stock removal and another for the fine finish...but you could just get a Shelix head and that problem is solved. Two planers doesn't make much sense unless you have lots of room and lots of money. I can't think of a single plausible reason to have two jointers. Two tablesaws is another one for the rich and spacious. I'd actually like to have three...one with a rip blade, one cross-cut and another for the dado stack. On second thought, make it four...I'll take a slider, too. Not gonna happen for me. But two bandsaws...definitely. I'll be adding a second bandsaw this year so I can have one set up for rip and resaw and another for tight curves. I think two bandsaws makes sense, and not even in an extravagant way but in a real-world time-saver practical way. I'd like to have four random orbit sanders so I don't have to keep switching discs as I move through the grits. If I didn't use Festool sanders that might not be unrealistic. And of course, everyone needs at least a dozen routers. I'd like to have two router tables or add a shaper...it'd be nice to have something permanently set up for template routing because I do so much of it. I've been thinking about getting a small shaper and a Shelix head for that for a while. That would definitely be a luxury. 1 Quote
Llama Posted November 28, 2013 Author Report Posted November 28, 2013 Awesome thoughts on two or more of one tool. Quote
Cochese Posted November 28, 2013 Report Posted November 28, 2013 I'll have two planers in the shop tomorrow:) Sent from my HTC One using Tapatalk Quote
wintersedge Posted November 28, 2013 Report Posted November 28, 2013 I have two planers. A Bailey 4 1/2 and a Bailey 5 1/2. Didn't see a need for two jointers... Wait... Wrong forum to make these comments. 1 Quote
Tpt life Posted November 28, 2013 Report Posted November 28, 2013 Eric: food for thought. I am guessing you cannot think of a single plausible reason for two jointers because you do not edge joint anything but 90 and you do not use a jointer to rabbet. If you do either of these things I think a permanent 90 setup on a second machine would be a big plus. 1 Quote
Eric. Posted November 28, 2013 Report Posted November 28, 2013 Good point, Shaffer. I'm all 90*...do my rabbeting and bevels on the TS. I could tack weld my jointer fence at 90* and it wouldn't make a difference in my shop. Quote
Llama Posted November 28, 2013 Author Report Posted November 28, 2013 I have two planers. A Bailey 4 1/2 and a Bailey 5 1/2. Didn't see a need for two jointers... Wait... Wrong forum to make these comments. I have plenty of hand planes, with more always on the way Quote
Tom King Posted November 28, 2013 Report Posted November 28, 2013 "I'd like to have four random orbit sanders so I don't have to keep switching discs as I move through the grits." I've done that long enough that I've had to redo the Magic Marker grit numbers on the sanders a bunch of times. 1 Quote
Tom King Posted November 28, 2013 Report Posted November 28, 2013 I have plenty of hand planes, with more always on the way This is a subject that I really, probably, shouldn't talk about. Excuse me. I need to go check my ebay Watch List. 1 Quote
Freddie Posted November 28, 2013 Report Posted November 28, 2013 I have plenty of hand planes, with more always on the way Not after this christmas mel, wait til you see my collection Quote
Llama Posted November 28, 2013 Author Report Posted November 28, 2013 Not after this christmas mel, wait til you see my collection I don't usually compare, but we can play Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.