Recommended Posts

Posted

Time for a little power tool gloat.  I just received my Hammer A3-31, it looks like it will be a sweet machine!!  It arrived today with only a minor amount of shipping damage.  The plastic dust collection shoot was busted so I had to improvise with the dust shoot from my lathe, until Hammer gets me a new one.

 

post-6663-0-93479900-1388799409_thumb.jppost-6663-0-44268200-1388799422_thumb.jppost-6663-0-66685800-1388799429_thumb.jppost-6663-0-53018000-1388799436_thumb.jp

  • Like 1
Posted

Time for a little power tool gloat.  I just received my Hammer A3-31, it looks like it will be a sweet machine!!  It arrived today with only a minor amount of shipping damage.  The plastic dust collection shoot was busted so I had to improvise with the dust shoot from my lathe, until Hammer gets me a new one.

 

attachicon.gifHammer.jpgattachicon.gifHammer1.jpgattachicon.gifHammer2.jpgattachicon.gifHammer3.jpg

 

Ditto!

Posted

First use and findings with the new Hammer.  Now keep in mind I don't have a huge experience with different machines, I have owned two different jointers, 30 year old Sears and a new Powermatic 6" with spiral cutter head, which I owned for two years.  My only experience with a  planer was my Rigid 13" lunchbox machine.  

 

I started a new project yesterday, an audio equipment rack, it is loosely based on Marc's G&G blanket chest.  I couldn't get 5/4 material for the base so I had to resaw some 8/4 and then plane it down to final thickness.  

 

My first impressions of the new Hammer........It's amazingly quiet compared to the Rigid planer but I think anything would be quieter.  The Euro style blade guard will take some time to get accustomed to but in time I will like it.  The surface of the jointer in feed and out feed tables are rougher than I would have thought, my Powermatic tables were as smooth as smooth gets.  This rough surface seems to add a bit of friction to sliding things a crossed it compared to the Powermatic when it was clean and waxed.  If the PM wasn't clean and freshly waxed then it wasn't so easy to slide lumber across  either.  I'm pleased with the quality of cut I'm getting from the Silent Power cutter head, very smooth other than edge jointing, I believe my PM gave a little smoother cut on edge jointing, but I always make a couple of passes with my smoothing plane on those edges anyway before gluing.

 

The service tech I spoke with told me to be sure to hold the power button down until the machine comes up to full speed before taking my finger off the switch so as to extend the life of the starter capacitor.  The on/off switches are momentary type switches, the PW switch is a mechanical lock type switch.  I have taken that advice but I don't see how it could be an issue as the machine comes up to full speed in about a half a second.  As for power this thing seems like it will never run out, it eats 8/4 cherry like it's hot butter.

 

The dust collection is good and I'm sure if I had a stronger motor on my dust collector it would be even better, I get a few pieces of wood laying around when I run the planer.  My dust collection is a Clear Vue cyclone attached to a Harbor Freight motor and impeller, with 6" pvc pipe then going to a 8' piece of 4" flex hose.  The Silent Power cutter head makes the smallest shavings I have ever seen.  The chips aren't just small chips it's like little rolled up pieces of wood.  I believe the Hammer video is correct when they say you won't have to empty your dust collector as often.

 

I bought a few accessories for the machine.  I got the digital readout on the hand wheel crank for the planer depth and it was money well spent.  I also got two of the extension rail adapters and one short extension rail.  I put one rail adapter on the planer out feed and one on the jointer out feed.  I put the extension rail on the planer which I think it needs all the time.  I believe the rail on the out feed side of the planer is a must to help control snipe which is almost none.  As for the out feed of the jointer, well I haven't really needed it yet working with lumber only 4' long or so.  If I were working with longer material it would be nice to have that out feed support.  I thought I could easily move the extension rail from planer to jointer but that is not really the case.  The rail uses a clamping device to hold it firmly in place which is designed so that when you loosen the clamp the rail would slide off the end of the rail adapter.  Well when the rail is on the planer out feed it can't slide off the end, it has to lift off which means you have to completely remove the clamping device.  I will just leave it on the out feed side of the planer and perhaps make some extensions from maple for the in feed and out feed of the jointer when I really need them.

 

As for the jointer fence, this is my least favorite part of this machine.  To be honest I don't move my jointer fences very often so I don't think it will be a big deal but I don't think it's that great of a design, it would be better if it were a little stronger.

 

I think most people, my self included, fear the change over time from jointing to planing and back.  I decided I would learn to live with it because my shop is my two car garage and I was running out of floor space, I just didn't have enough room for a large stand alone planer like  PM 15" or 20" machine.  Like all new equipment there is a learning curve but the time to change over from one operation to the other really isn't long at all.  To be honest it's much faster than what I did to set up my old Rigid planer and then that planer was in my way for other operations so this is a much better solution for me.

 

Like anything new it will take time to get acclimated, like remembering to engage and disengage the feed rollers of the planer, its doesn't feed worth a crap if you don't remember to turn on the feed rollers.   Then of course you must remember to turn them off so as to not prematurely wear out that part of the machine.  Also I will help to remember to crank the planer table back down before trying to flip the dust shroud back over.  You don't have to crank the planer table all the way to the bottom, you can stop 2" shy of the bottom when switching back to jointer from planer.  When switching from jointer to planer you must crank the planer table back up from the 7" point to the desired cut depth which most of the time will be 3/4".  I know for many this is the key complaint against a combo machine but it really only takes a few seconds to spin that crank, and with the digital readout you can come back to the exact same depth over and over again.

 

Everyone always ask, "Would you buy it again", for me yes I would, but it's only been one day of use so give me a week and lets have this conversation again.

Posted

Steve I just ran a few more board feet through the machine and I would now say an extension on the out feed side of the Jointer would be nice to have.  The lumber I was milling was around 55" long with a slight bow to it, I was in the high point of the bow when the end of the board was falling off the end of the jointer so an out feed extension should have been in use to get ultimate flatness. The Hammer extension tables have a bolt on the underside which allows you to adjust the extension to perfect level or up or down compared to the jointer or planer tables.  If you have a table set correctly, i.e. level for one operation and then remove it and move it to the other part of the machine then it won't be correct for that operation.  Now I would say either build your own extensions or buy two of them from Hammer depending on what length you feel you need, one for the planer for sure and one or two more for the jointer.  For someone that only makes very small projects then they won't be as useful.

Posted

==> but it's only been one day of use so give me a week and lets have this conversation again.

Think what would really help the community is a six-month and twelve-month check-in...

 

All machines are great for a few weeks -- or until the cosmoline-induced-stupor wears off -- whichever comes first :)

 

It usually takes me a few months to really start second-guessing a purchasing decision...

 

Further, most folks are suspicious of combo machines due to the more complex mechanism... Longer-term reliability feedback would add real value for the community...

 

If you could, please check back after you discover the warts-and-all...

 

Thanks in advance...

  • Like 1
Posted

"Cosmoline induced stupor"  :D  That's a good one that I will need to remember!!  I will certainly keep everyone posted as the new wears off.

 

As for added complexity I only see the fact that the jointer tables tilt up out of the way as added complexity.  As long as the hinge points don't wear easily and the stops stay in place then I don't see this as a big problem.  But you are certainly right, only time will tell for sure.

  • 4 months later...
Posted

The new has now worn from the Hammer and it has developed it's first problem.  Seems that a starter capacitor is going bad, or at least I hope it's that simple.  The unit over heats and shuts down after only 10 minutes of use.  Hammer is sending me a new capacitor and I will get that installed on Tuesday and then see how is performs.

Posted

The new has now worn from the Hammer and it has developed it's first problem. Seems that a starter capacitor is going bad, or at least I hope it's that simple. The unit over heats and shuts down after only 10 minutes of use. Hammer is sending me a new capacitor and I will get that installed on Tuesday and then see how is performs.

Is this part covered by warranty? And no cost to you?

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Who's Online   3 Members, 0 Anonymous, 59 Guests (See full list)

  • Forum Statistics

    32.1k
    Total Topics
    437.6k
    Total Posts
  • Member Statistics

    26,009
    Total Members
    3,644
    Most Online
    Joseph b
    Newest Member
    Joseph b
    Joined