joshhulbert Posted January 10, 2014 Report Posted January 10, 2014 Is anyone out there using the dampener/stiffener from Forrest for their table saw blades? I'm looking at getting a Forrest Woodworker II and was wondering if it was worth picking one up at the same time. Quote
STL Woodguy Posted January 10, 2014 Report Posted January 10, 2014 To be quite honest with you, some people swear by them but this is one of the few purchases I regret, I have the thing sitting in the shop somewhere collecting dust. The biggest problem with it is that it limits your cutting depth. Otherwise, I feel my saw without it cuts fine. I would just purchase the WWII blade and see how you do without it first. Quote
Hybrid-woodworker Posted January 10, 2014 Report Posted January 10, 2014 I use a forest, no stabilizer and go right to glue up. I do have link belts on TS but don't find the need to joint, post ripping. BRuce Quote
wdwerker Posted January 10, 2014 Report Posted January 10, 2014 I use thin rim blades and a blade stiffener does help with the quality of the cut. I had some Forrest blades in the past but don't use them currently. Quote
Freddie Posted January 10, 2014 Report Posted January 10, 2014 I think they really shine on the thin kerf blades. I use full kerf, and havent found a need for a stablizer yet. Quote
Freddie Posted January 10, 2014 Report Posted January 10, 2014 Jeez, all my comments are getting posted by others as i am literally typing them haha Quote
Trip Posted January 10, 2014 Report Posted January 10, 2014 Without getting into signature series or blades from his custom shop, Jim makes three kerfs of 'standard' WWII 10" blades: 1/8", 3/32" and 5/64". The 5/64 is extremely useful for certain applications and the stiffener is required for safe use... Some folks use the stiffener on 3/32 and swear by it, some don't think it provides any benefit at all -- probably 50/50... I'm not sure anyone uses a stiffener on Forrest's 1/8" kerf blades and wouldn't think it provides any benefit at all... Quote
Tom King Posted January 10, 2014 Report Posted January 10, 2014 I bought one way back when I got my first Forrest blade. I don't have any of the thin kerf blades, and never needed the stiffener for anything. Quote
dwacker Posted January 10, 2014 Report Posted January 10, 2014 They do help on 12 -18" saw not so much on 10" with full kerf blades. Quote
joshhulbert Posted January 10, 2014 Author Report Posted January 10, 2014 Thanks for all the feedback! I will most likely be doing the full kerf blade so it doesn't sounds like this should be much of an issue. I think I'll go with just the blade for now and see how it goes - thanks! Quote
wdwerker Posted January 11, 2014 Report Posted January 11, 2014 A 3/32 kerf rip blade = more horsepower going to a narrower kerf. I use them on my 120 volt 1 1/2 hp UniSaw. Plus it give me a bit more room when making multiple rips from a sheet of ply. Some of my suppliers carry 48 1/2" by 96 1/2" American made hardwood ply which is nice for cutting full size pieces, instead of making them 1/8 under to allow for the saw kerfs. Quote
knotscott Posted January 11, 2014 Report Posted January 11, 2014 Forrest makes really good profit on those things, so naturally they recommend them. I've never noticed a difference with or without them when using a good blade on a well tuned saw. Some notice a difference but the comments I've read suggest that the majority don't benefit from them. A saw with low runout that's setup properly with a good blade shouldn't need them....I suspect that those who benefit from them are often putting a band-aid on a bigger issue. I'd recommend against until the need proves itself...in which case, I'd suggest tracking down the source of the problem. Quote
dwacker Posted January 11, 2014 Report Posted January 11, 2014 Some of the larger blades put off a deafening high pitch scream especially 14" and 18". The dampener stops this scream. There is no need for them on smaller saws. They do quiet the saw slightly but since the saw is not screaming to begin with the difference is barely noticeable. You would have to hear a real industrial saw without a dampener to truly understand what they actually do. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.