pghmyn Posted January 23, 2014 Report Posted January 23, 2014 On the other side of my bedroom wall is a walk in shower. Whenever the shower is turned on, it is just as loud in the bedroom as it is in the bathroom. If I had to type the sound, it is, "SSSHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH" Is there any way to quiet this sound without tearing anything down? I do not want to do any demolition or pour money into this. So, if there is a simple fix, it would be amazing to know. Also, does anyone know the cause of this? Quote
Freddie Posted January 23, 2014 Report Posted January 23, 2014 It's the shower valve body in the wall. Installation of the shower system recommends insulating the walls during construction to help dampen this. In your situation, minimal evasiveness would be to poke a hole in each bay of the wall from the bedroom and insert the loose fill insulation using one of those hoppers. Other than that, deal with it Quote
wdwerker Posted January 23, 2014 Report Posted January 23, 2014 There is no such thing as a quick fix in this situation. Pull the sheetrock, insulate the cavity, install sound deadening board and then new sheetrock. Homasote is one brand of sound deadening board, it looks like the board they make bulletin boards from. Another approach would be to cut a small hole top bottom and middle of each stud space and use the low expansion squirt foam. Be careful! Too much foam can buckle the sheetrock out into the room. Then patch the holes and repaint. Quote
Tpt life Posted January 23, 2014 Report Posted January 23, 2014 Neatest looking and quietest bedrooms I ever worked on: Homasote milled to random widths and beaded. We installed it vertically and painted it like paneling. Super quiet, almost anechoic. Want to be careful with how you insulate around and near plumbing fixtures. Things grow where you trap moisture. Quote
sjeff70 Posted January 23, 2014 Report Posted January 23, 2014 You could try installing Quiet Rock drywall over your existing drywall. Lowe's used to carry it...you should be able to order it from there? Also insulate around your receptacle and switch openings. 1 Quote
pghmyn Posted January 23, 2014 Author Report Posted January 23, 2014 I might look into some small bit of spray foam into the wall. But I'm uneasy about the idea of it expanding too much. I don't want to cut down or remove the drywall. I have never done drywall finishing, and now is not the time for me to learn. Quote
Freddie Posted January 23, 2014 Report Posted January 23, 2014 Use door and window foam, it doesnt expand and blow out like the normal gap filler. Quote
pghmyn Posted January 23, 2014 Author Report Posted January 23, 2014 Can I spray in just the void that has the pipe? Quote
Tpt life Posted January 23, 2014 Report Posted January 23, 2014 You mean bay (stud to stud?) Yes. Just pray you never need to change anything. :-) Personally I would not spray foam or loose fill. That valve is not a tight fit to the wall or tub. It relies on escutcheons. You run the risk of getting insulation where you don't want it. Quote
pghmyn Posted January 23, 2014 Author Report Posted January 23, 2014 You mean bay (stud to stud?) Yes. Just pray you never need to change anything. :-) Personally I would not spray foam or loose fill. That valve is not a tight fit to the wall or tub. It relies on escutcheons. You run the risk of getting insulation where you don't want it. I could possibly go in the attic and pack down from the top by drilling an access hole in the top plate. Just brainstorming, not sure if that would work. Quote
wtnhighlander Posted January 24, 2014 Report Posted January 24, 2014 Opening the wall is your most effectve route. Don't be afraid of patching the wall board, just be patient. One way to avoid some of the mess is to gently wipe your dried mud / spackle with a well dampened sponge to smooth it. Works pretty well, and no sanding dust. Get a big sponge like are sold for cleaning tile grout, and drag it across with light pressure.Sent from my XT1058 using Tapatalk Quote
..Kev Posted January 24, 2014 Report Posted January 24, 2014 Highlander is correct, there's not a lot to drywall. It's not hard. If you're going to go to this length, then Wdwerker was correct with the soundboard. The only addition I would make to his post would be to add a lathing strip between the soundboard and the drywall. This will increase the sound proofing with only about 1/8 lathing strip. 1 Quote
wdwerker Posted January 24, 2014 Report Posted January 24, 2014 If you have attic access to the wall from above and basement access from below you could use the door and window foam through holes drilled into the wall cavity and possibly remove the escutcheons and squirt foam in from there as well. Be careful if that stuff gets on your hands it very tough to get off. Same applies to shower tiles , carpet and other household surfaces. Gloves , drop cloth's ,masking tape etc should be used liberally ! I would bet that you could use a plastic tube to extend the one on the foam can for a longer reach. Might be worth a test run in a garage or basement wall for starters. Could take quite a few cans. Quote
Spencer_J Posted January 26, 2014 Report Posted January 26, 2014 I like everyones ideas above. What about getting one homasote panel and gluing it to the wall where the valve is? You could paint the panel an accent color if it turns out to work well. Any metal fasteners would help transfer the sound, hence the glue. Low cost/ labor hours. Sent from my thumbs Quote
Janello Posted February 9, 2014 Report Posted February 9, 2014 I would try the easy route first. Put a different shower head on. Make sure to take the water saver washer out. Sometimes a restriction in flow at the shower head can make the valve body make more noise. Think, pinching a garden hose. Quote
wtnhighlander Posted February 9, 2014 Report Posted February 9, 2014 Hate those low-flow heads. Put one it a while back, but had to run around it the shower to get wet. Ended up taking it apart and drilling the orifice in the 'knuckle' out to 1/4". Now it's a real shower! 1 Quote
pghmyn Posted February 13, 2014 Author Report Posted February 13, 2014 I like the idea of looking at the low-flow mechanism. I don't want to say that I am against conserving water, but if that is what is what is causing the problem it might just have to go! I think we pay $0.01 per 5 gallons of water here in Milwaukee, so I can't see the cost difference being too much Quote
wdwerker Posted February 14, 2014 Report Posted February 14, 2014 I think low flow bath faucets work fine to wash your hands, shave etc. And low flow toilets(the ones that really work) are ok as well. But a low flow shower is a quality of life decision. Not enough pressure and it's a waste of time in my book. Quote
pghmyn Posted February 14, 2014 Author Report Posted February 14, 2014 I think low flow bath faucets work fine to wash your hands, shave etc. And low flow toilets(the ones that really work) are ok as well. But a low flow shower is a quality of life decision. Not enough pressure and it's a waste of time in my book. I think the shower head says 3 gallons per minute, how low is that compared to a normal shower flow? EDIT I can't stand low flow toilets, especially ones in new-ish built houses. The one at my parent's house is 30 years old, and still works just as good as it did on the day they moved in! Then again, I'm not sure how much water they use, but the friggin' jet engine toilets at my work are just impressive. I want one at home. Blink of an eye and whatever you can throw at that toilet is gone. Getting a little off topic with that, but I couldn't help it. Quote
Tpt life Posted February 14, 2014 Report Posted February 14, 2014 Restrictions cause noise. I would question if all supply lines and valves are properly sized. Some noise will be there anyway because to get jetting pressure from the head, you create obstruction. Think thumb over the end of a garden hose. The supply for the head is attached directly to the framing that carries your wall on the bedroom side. I would also check the line pressure of your water supply just to be thorough. If the noise feels excessive to you, I would recommend talking to a friendly plumber or cutting the wall open. The best and most thorough solutions can be achieved with line of sight on all components. Quote
Tpt life Posted February 14, 2014 Report Posted February 14, 2014 Another thought, how old is the shower valve? Any chance is has lime buildup that could be removed? Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.