Lapuawood Posted March 28, 2014 Report Posted March 28, 2014 I'm hoping someone can help with some advice. I want to make a very sharp profile on an oval table project. I have attached a picture of my aspiration. The table is going to be very large, so I need to have a router bit that indexes off the top edge all the way around. Does anyone have a router bit suggestion or another process that will produce this result easily? Thanks! Quote
Pbmaster11 Posted March 28, 2014 Report Posted March 28, 2014 My opinion you would be better off using hand planes and raspsTyping on cell phone. I apologize for any typing errors. 2 Quote
..Kev Posted March 28, 2014 Report Posted March 28, 2014 Agree with PB.. Best to flatten that way and then maybe run a small radius router bit over the end.. Quote
wtnhighlander Posted March 28, 2014 Report Posted March 28, 2014 A large, bearing guided chamfer bit might form the under side of the profile, but you will have no surface left to register a round over or thumbnail bit for the final edge. Could you possibly make a template of hardboard or something, that matches the shape of the top and provides a guide surface for the final routing operation? I'm thinking a fingernail profile with a guide bushing and a template would do the trick.Having said all that, I have to note that the slope of the chamfer inbthe photo is steeper than any chamfering bit I recall seeing. Maybe there is a raised panel bit available with that slope, though. I hear some bit makers will provide custom profiles if you are willing to foot the bill. Quote
tim0625 Posted March 28, 2014 Report Posted March 28, 2014 Different thought process but what about a jig that cradles the router at an angle that you can just move around the circumference? That would get it close and then a little round over for the edge, some sanding and you're there? Quote
Beechwood Chip Posted March 28, 2014 Report Posted March 28, 2014 There's a trick I learned from a Charles Niel DVD. You put a layer of MDF under the table edge, and use a trim bit so that it exactly matches the table top. Then, use a rabbeting bit to create a guide that follows the edge a set distance in from the edge. Then you can index off of that to cut into the table top. This can be repeated several times to cut a deep profile. Charles used this on his pie crust table project to make a very complicated edge, that would otherwise have to be carved by hand. You could use this to approximate the underside of your edge, and then finish with a sander or rasp. Quote
wdwerker Posted March 28, 2014 Report Posted March 28, 2014 I was thinking of the tablesaw jig that Mathias guy used to cut his wheel for the scaffold. If you had a pivot pin for the underside of your tabletop and raised the blade in tiny increments then spun the top and repeat until you had cut the entire bevel. Quote
krtwood Posted March 28, 2014 Report Posted March 28, 2014 http://www.mlcswoodworking.com/shopsite_sc/store/html/smarthtml/pages/raised_panel_router_bits1.html Something like 8673 at the bottom of the page. You'd then have to finish off the rest of the bevel by hand but it sure beats trying to do it all by hand and it would leave you a place for the bearing to ride against. Quote
Marco Divetta Posted March 28, 2014 Report Posted March 28, 2014 I think this is one of those times that the hand tool rout would be better .... I remember seeing a video recently ( maybe you guys can help ) where the crafts man was trying to achieve a similar chamfer , he marked the edge and bottom of the surface outlining the chamfer and then used a hand saw to cut straight down every inch or so until he was about 1mm away from both lines, he then blew the 1" blocks with a chisel removing most of the waste and then he planed down to the desired finish. Quote
Marco Divetta Posted March 29, 2014 Report Posted March 29, 2014 Band saw? A bit of Sam maloof influence Quote
wilky101 Posted March 30, 2014 Report Posted March 30, 2014 hi all. why not try a shaper with an auxilllary table....is the piece too large? or perhaps there is a way to use a shaper style 1/2 shank router bit with a fence attatched to your hand-held router? Quote
wilky101 Posted March 30, 2014 Report Posted March 30, 2014 I just had a better idea(or so i think lol) rout the bottom with a bearing-guided chamfer bit (as krtwood suggested), then use a small roundover bit for the topside but mount the fence to your router so the bearing doesnt come into play. The only problem i see with this idea is that it doesnt leave any telltales of handcrafted work.....it may look too regular....it depends what style piece your looking for i suppose. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.