Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Pattern Routing Workpiece Holding Jig

Featured Replies

  • Popular Post
Fine Woodworking magazine for the month of July/August 2014 issue 241 has plans for a Smart Jig for Pattern Routing by Tim Celeski to hold a template and work-piece when pattern routing. Over the years I have made occasional jigs to do such things but they have always worn out, broken or fallen by the wayside. So I decided to make the one described by Tim in the magazine. Credit for the design goes to Tim and full details are in the magazine.
 
Construction
Essentially it comprises:
  • a base 10" x 17" made from 18mm plywood (preferably baltic birch 3/4")
  • a clamp plate 8" x 17" made again from 18mm plywood
  • a hardwood fence, in my case an oak scrap, glued onto the clamp plate
  • 8 off 3/8" captive T nuts
  • 4 off 10mm (3/8") washers
  • 2 off 3/8" star knobs
  • 2 off self adjusting toggle clamps
  • 8 off M5 x 40 long countersunk head socket screws with nuts and washers (or equivalent imperial). 
The hardwood fence is glued to the top plate and cut away to clear the star knobs when they are in the forward position.
Drill 2 columns of 4 holes (8 in total) for the T-nuts in the base plate. These start 3-3/8" from the front of the longest edge of the base plate on 15" centres. The remaining  3 pairs of holes are drilled inline with the first two on 1-1/4" centres.
Next counterbore these holes on the underside of the base plate with a Forstner bit to clear the head of the T-nuts. Then the T-Nuts are inserted from the underside and hammered home.
 
IMG_0368-001.JPGUnderside of base plate showing the counterbores for the heads of the T-nuts
 
The two slots in the clamp plate are routed to line up with the base plate holes again on 15" centres as clearance for the threaded shafts on the star knobs.
 
IMG_0367.JPG
 
Top view of  the full assembly (Note there is no workpiece shown here)
 
The toggle clamps are positioned on 18mm spacers centrally in 7" centres. The spacers are glued and pinned to the clamp plate. The clamps are bolted permanently onto the clamp plate after drilling for the 8 - M5 screws. The holes for the M5 screws are countersunk on the underside of the clamp plate.
In the article Tim suggested using captive T-nuts on the underside with screws holding the clamps from the top but I didn't have any small T-Nuts so used the method above.
 
A hole is then drilled to hang the jig up.
 
Usage
In practice you can position the work to be routed complete with its pattern onto the baseplate. You then adjust the fence by positioning the star knobs into whatever hole is suitable and finely adjust the clamp plate on the slots. Tighten the star knobs and tighten the toggle clamps. You can then use a pattern routing bit to follow the profile of the template and cut the work-piece to shape. (photos below taken from the article while viewing it on an ipad)
 
IMG_0375.JPG
 
IMG_0376.JPG

Awesome..  Now there's a jig I don't have in the shop but, will soon build for sure!

Got one built today..  Now I just need a project to use it on ;)

 

Oe1IST.jpg

This will be on my list of jigs to build. Have the wood just need the hardware. I was making my chairs with templates and would have felt a lot better with this!

  • 2 years later...
15 minutes ago, Lester Burnham said:

Holy #$%^ where was this thread when I needed it last year? That's awesome!

Apparently it was right here - it's dated 2014! ;)

 

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,009 Total Members
  • 3,644 Most Online
  • Joseph b Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.