Tom Cancelleri Posted November 28, 2014 Report Posted November 28, 2014 Not a bad deal. Rigid variable speed trim router, and 1/4 sheet sander. $99 Thoughts on the router? http://www.homedepot.com/p/RIDGID-5-5-Amp-Trim-Router-with-Free-1-4-in-Sheet-Sander-R24011/202488411 Quote
TerryMcK Posted November 28, 2014 Report Posted November 28, 2014 Having a trim router is always a good thing but just make sure you can operate it with one hand. I use my similarly rated Dewalt DW670 primarily for doing round overs and occasional edge band trimming (what it is designed for). I think from what I remember about the Ridgid is that it has two speeds. Always useful to have a very long power cord on these tools too - check to see. Overall as they are throwing in a palm sander too it looks like a good deal. Quote
Tom Cancelleri Posted November 28, 2014 Author Report Posted November 28, 2014 8 foot cord and variable speed. For the price, it'd be hard to pass up. I've got an old single speed trim router that's miserable to use. 1 Quote
dwacker Posted November 28, 2014 Report Posted November 28, 2014 Ive owned the rigid. Had it on a little diy cnc engraver for a little while. It was fine for that but once it started getting used for its intended purpose it died quickly. Quote
Cochese Posted November 28, 2014 Report Posted November 28, 2014 I looked at it when it went down to $89 and I passed. I think for what I want, I should look for other options. The Dewalt is tempting due to dust control attachments. I was also made aware of a design flaw in the soft start mechanism. It can be fixed if you like to solder, but I don't particularly. Quote
Tom Cancelleri Posted November 28, 2014 Author Report Posted November 28, 2014 Digital electronic repair was one of my courses in college. Soldering labs, building networking equipment and phones as projects and exams. I could solder. I'm not in any rush to get a new one but if it was worth it, I'd get it. I would love the mfk 700 but oh so much money. Quote
Cochese Posted November 28, 2014 Report Posted November 28, 2014 Completely baffles me as to why it is more expensive than the 1010. Quote
wdwerker Posted November 28, 2014 Report Posted November 28, 2014 The Dewalt dust attachment is ok, not great. The Dewalt is a pretty nice trim router. The lights and clear base really let you see well when you need to work up to a mark. The MFK 700 has 2 ways to attach the vac, the beside/ below the bit accessory works better than any of the over the bit ones do. Visibility is almost zero. Not an issue for the things I use it for but it should be noted. The ability to make super fine adjustments is quick and easy. The horizontal baseplate has similar adjustments and trims solid wood edging strips wonderfully. I don't have a very high opinion of much that Ridgid makes. The one exception is the Osselating belt sander, great little machine especially for its price. When years of abuse killed mine I went right out and got another! Quote
Janello Posted November 28, 2014 Report Posted November 28, 2014 spend the extra hundred, get the DW with a plunge accessory and you won't have a useless sander on your shelf. Quote
Tom Cancelleri Posted November 29, 2014 Author Report Posted November 29, 2014 spend the extra hundred, get the DW with a plunge accessory and you won't have a useless sander on your shelf. You name a very valid point. That sander wouldn't touch any of my projects. It's more of a use it on the hand rails of my deck. Quote
Vyrolan Posted November 29, 2014 Report Posted November 29, 2014 One observation is that $100 would buy you 3 of the Harbor Freight trim routers with $40 left to buy a bit to dedicate to each one. Never deal with changing bits...just grab and go. Sure it's not the best router, but if you're just running a 1/4" roundover or other trim router tasks it would probably be fine. Quote
krtwood Posted November 29, 2014 Report Posted November 29, 2014 One observation is that $100 would buy you 3 of the Harbor Freight trim routers with $40 left to buy a bit to dedicate to each one. Never deal with changing bits...just grab and go. Sure it's not the best router, but if you're just running a 1/4" roundover or other trim router tasks it would probably be fine. Just one of the HF trim routers will permanently stink up your shop. Three of them at once might be lethal. Seriously, 100 years from now that router will still be emitting a wondrous stink. I'd charge them $100 to take another one off their hands. Quote
wdwerker Posted November 29, 2014 Report Posted November 29, 2014 Do they truly make a smell? I have stooped to getting a few things at harbor freight but never tried much in the way of power tools. The 23 gauge micro pin nail guns are pretty good for the price. Shoots up to a 1" headless pin. Quote
Tom Cancelleri Posted November 29, 2014 Author Report Posted November 29, 2014 I buy my shop materials at HF. Brushes, rags, gloves, cleaners, wire wheels. If I'm doing any round over work I'd either run it over my router table with my PC 7518, or use my Bosch 1617 EVS. My needs for a trim router are some counter top building/laminating for some shop cabinets, guitar binding channel routing, and maybe if I go the plunge route, maybe chamfering dog holes when I build my new bench. Quote
krtwood Posted November 29, 2014 Report Posted November 29, 2014 Do they truly make a smell? I have stooped to getting a few things at harbor freight but never tried much in the way of power tools. The 23 gauge micro pin nail guns are pretty good for the price. Shoots up to a 1" headless pin. It's not just that it stinks when you first get it which sometimes happens with cheap chinese stuff, it just keeps on stinking every time you turn it on. They didn't just pack in something horrible smelling, it's greased inside with the stuff. Quote
Raefco Posted November 29, 2014 Report Posted November 29, 2014 I use some harbor frieght stuff especially in the field, when their "high end" stuff cost 1/10 what a Milwaukee or matabo does... I cooked a soft start matabo last time I was In Chicago on a job, granger and fastenal both gave me the famous line "I can have what ever you want tomorrow" well buddy, I'm going to be back home tomorrow, so I bought a $29 harbor frieght grinder and have been using it daily for the last 6 monthes. Don't get me wrong, I love good tools, but most of the Dewalt and Milwaukee stuff is made in China as well, they are making it awful hard for a union guy to be loyal. Quote
wtnhighlander Posted November 29, 2014 Report Posted November 29, 2014 I think that is a unique occurrence. I have several powered tools from HF, including a router. None of them smell. Quote
Tom Cancelleri Posted November 29, 2014 Author Report Posted November 29, 2014 My cousin bought a hf 12 ton press a few weeks ago. Out of the box the bottle Jack didn't work, upon assembly one of the plate bolts exploded when being tightened. Quote
TerryMcK Posted November 29, 2014 Report Posted November 29, 2014 I buy my shop materials at HF. Brushes, rags, gloves, cleaners, wire wheels. If I'm doing any round over work I'd either run it over my router table with my PC 7518, or use my Bosch 1617 EVS. My needs for a trim router are some counter top building/laminating for some shop cabinets, guitar binding channel routing, and maybe if I go the plunge route, maybe chamfering dog holes when I build my new bench. I actually use a Dremel with the precision router base and the guide wheel assembly combined with a 7mm router bit (1/8" shank) to rout the guitar binding channels. I don't trust a higher powered router just in case it slips and runs away. At least with the Dremel you can let it bog down. Quote
Vyrolan Posted November 29, 2014 Report Posted November 29, 2014 It's very hit-or-miss with them. Kinda like how Steve said earlier in the thread about Ridgid (only the belt/spindle sander has much value). The same can be true of HF...there can be some diamonds in the rough. Quote
wtnhighlander Posted November 29, 2014 Report Posted November 29, 2014 It's hit or miss even among instances of the same tool. I've learned to examine each carefully before I buy. And keep expectations reasonable. Quote
Eric. Posted November 29, 2014 Report Posted November 29, 2014 My only HF tool is a die grinder. Works fine except it gets unbearably hot and impossible to hold after about three minutes of use. Haven't smelled anything. A HF hoist nearly decapitated my toes once when moving my 15" planer. Quote
Raefco Posted November 29, 2014 Report Posted November 29, 2014 Your toes have heads? Holy cow, I don't know how well I could deal with a consensus of 12, 2 is a battle Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.