Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Bell plaque

Featured Replies

For whom the bell tolls! Got a commission yesterday to build a Plaque to mount a bell to, and apparently now a bull dog shaped bottle opener. He called me right after I cut the wood to make a change. I told him that there would be no more wood after the change since the first cuts were already made. a9f7dfb79a4c2cd747a79c5738f75cd1.jpg Flooring sample, the Orange in the floor gets really complimented by the mahogany. bbe149456305dec1ab32c4e48270411f.jpg Flattening the joint to be gapless 6c4a0cfb516745cdcbcf02f9b5359a10.jpg Dominoes, because I wanted some added strength. Some 5x30 beech dominoes. 1552e2563a5868ece7ed64fd83acb77a.jpg Glue and clamps c27b8b413599834189d54ce9b1a4882b.jpg Sent from my 831C using Tapatalk

  • Replies 71
  • Views 11.4k
  • Created
  • Last Reply

Top Posters In This Topic

Most Popular Posts

  • Author

Awesome!! What are you using to joint? Laj?

Bevel up jointer from Veritas. Sent from my 831C using Tapatalk
  • Author

Drum sanding the panel flat. Nice and flat and parallel, just how I like my panels. I use pencil lines across the entire board to make sure there are no high or low spots. 50ee2e8551797e78f090bde38dfca382.jpg Sent from my 831C using Tapatalk

  • Author

The wood was slightly cupped after glue up. Put it cup side down to flatten one side, then flip and repeat.

  • Author

Interesting. 

I couldn't plane both boards at the same time to clean the edges for glue up without getting tearout since one board had reversing grain edges weren't perfect 90

 

The confusion comes from,  if you glued up a panel that jointed slightly off of 180*, how did the drum not take care of that? 

Edited by Brendon_t

Infeed rollers push the slight cup down to the table then sands it. It flexes right back up afterwards. You can build a sled and use shims to flatten on a drum sander.

Drum sander needs a flat side to reference from like a planer does.

  • Author

A little pissed off at Festool. There's two marks on each side of the 1400. I was doing the key hole slots, had my lines and setup all good. Apparently one of the lines is offset from the bit center by about 1/8" I used that line to match up to the spots for the keyholes to hang it. Since the edge guide isn't long enough to do both from the same side due to the panel being 13" wide. That 1/8" translated to the keyhole being off. Luckily it's fairly easy to fix. Just made the top of the one that was lower longer, and adjusted based off the actual center line not the offset one.... Bad going Festool. Setups for each side 83347ee939d6a4f3d94022486a0e4a9a.jpgb8f01884125886a0a81b0997b04cb8aa.jpg Keyholes fa5226813470f43c73b510b15625333a.jpg Sent from my 831C using Tapatalk

  • Author

 

 

 

 

I adjusted my edge guide and it appears to be out of square. I have to really push against the bars to get it to line up properly. Not something that should be this difficult to get square on a router that's over 600 bucks. 

Edited by Tom Cancelleri

Ooohhhh my. Time to call festool! I guess they all have one made on Friday afternoon! Good luck with it Tom!

  • Author

Have you verified that your square is square?

Yep, checked with 3 different squares, including the woodpeckers big one Sent from my 831C using Tapatalk

Hmmm, weird.  Figure there's gotta be some easy adjustment on the edge guide.  Never had an issue so I've never looked.  I'm just glad the problem is yours and not mine. :D

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.