Brendon_t Posted September 9, 2015 Report Posted September 9, 2015 Hoping to lean on the hand tool guys for some info. I've been searching the interwebs for a relatively short bladed (18-22") hand saw in a crosscut tooth configuration.I've searched ebay, bad axe, a bunch of small boutiques and found NOTHING. Anybody know of a model of saw that comes in this length? Quote
mkirby Posted September 9, 2015 Report Posted September 9, 2015 Are you searching for panel saw?Under 24" is usually a panel saw and most makers made them.Like this one http://www.ebay.com/itm/Vintage-Disston-D-23-General-Purpose-20-Panel-Saw-11-ppi-INV151-/252078399021 Quote
Brendon_t Posted September 9, 2015 Author Report Posted September 9, 2015 It sounds like my nomenclature was keeping me from finding what I wanted.if a panel saw has no back, and fine teeth suitable for decent crosscuts, and is the length specified above, then that sounds like it's right.i am looking to use it for rough stock breakdown. I don't keep my mitre saw set up because it takes up too much room. I usually will clamp a long board in my face vice and take the hand saw to it. The home center hard point saw I have is just so aggressive it tears out every wood like crazy. Quote
Llama Posted September 9, 2015 Report Posted September 9, 2015 If you can't find what you need, call Mark at Bad Axe. He'll set you up. Quote
Brendon_t Posted September 9, 2015 Author Report Posted September 9, 2015 Hey Mel, I actually tried him first. Two emails to him but nothing back in a week. Figured I'd better keep looking. Quote
Gilgaron Posted September 9, 2015 Report Posted September 9, 2015 http://tgiag.com/ You can get a toothed piece of spring steel to your specs from these guys and make your own handle. They have templates, as does Blackburn tools. I haven't purchased a saw blade from them but I have some of their scrapers, which are excellent. If you want an induction hardened tooth saw there are plenty of hand saws like that at the hardware store. Should be some in that length or you could cut off the end with a dremel or angle grinder. That'd be the cheapest way, probably. Quote
derekcohen Posted September 10, 2015 Report Posted September 10, 2015 Also do a search on a "half back" saw. This is my Wenzloff ..Regards from PerthDerek Quote
collinb Posted September 10, 2015 Report Posted September 10, 2015 Sandvik 2600 is 19"https://www.google.com/search?q=sandvik+2600&ie=utf-8&oe=utf-8#q=sandvik+2600+hand+saw(I decided to keep mine. Also found it quite handy.) Quote
Llama Posted September 10, 2015 Report Posted September 10, 2015 Hey Mel, I actually tried him first. Two emails to him but nothing back in a week. Figured I'd better keep looking. That's really odd.. I either hit him up on FB, or call him. He's always been prompt. I can understand not wanting to wait for a response, especially after two weeks or so. Quote
Brendon_t Posted September 10, 2015 Author Report Posted September 10, 2015 Bought a nice looking disston. Hope it's decently sharp, otherwise I'm learning to sharpen. . Quote
Brendon_t Posted September 11, 2015 Author Report Posted September 11, 2015 (edited) Are you searching for panel saw?Under 24" is usually a panel saw and most makers made them.Like this one http://www.ebay.com/itm/Vintage-Disston-D-23-General-Purpose-20-Panel-Saw-11-ppi-INV151-/252078399021Btw, thanks for finding that. The saw shipped today. Edited September 11, 2015 by Brendon_t Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.