Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Resaw troubles, buy a Resaw King?

Featured Replies

I bought a new Laguna 14-12 bandsaw a couple of months ago and yesterday attempted to resaw some 7" cherry that was air dried and is 10 yrs old. I was using a new Laguna Proforce 3/4 blade. Well, things went pretty horribly. I did a lot more burning than slicing. I certainly wasn't going too fast, took me about 5 minutes to do a 2 ft long board. 

I'd certainly think the 14-12 would have enough power to get through 7" cherry. It is the problem the blade? Before I go out and spend $135 on a Resaw King I figured I'd check to ensure I'm not doing something wrong...

Thanks for the insight guys!

I will be looking forward to responses to this as well.  I haven't resawn yet with my 14-12 but I was planning on using the 3/4 blade you used for a XMAS project where I need to resaw some mahogany so you've probably saved my @#$%...thank you!

It sounds to me as if you have a dull blade or just a poor blade for resawing.

Since I build stringed musical instruments as a small business to supplement my retirement, I do a lot of resawing on my 14" delta with riser block.  I have found that I can get by fine with much less expensive blades than the Resaw King. The Timberwolf 3/4"X 0.025 TPC ($30 or so for 105") has worked great for me.  The resaw blades from Infinity Cutting Tools have worked nicely for me as well.

I just finished resawing some 7" cherry myself using the Infinity blade and it cut like butter and I think the Timberwolf might cut a little better if anything.  No way it should take anywhere near as long as you said it did, even with a sharp but inappropriate blade.  I didn't time it but I'd guess a 30" piece took maybe 30 seconds.  Definitely try a new blade.

You don't need a Resaw King to get the job done, but for some shops it might last enough longer to justify the cost.  Timberwolf and Infinity blades have worked well enough for me.  I personally would have to be in a higher production setting with a bigger saw before I'd consider one.  It may also give a better finish, I don't know.  I run always run the pieces through a thickness sander any way do the smoothness is plenty good enough with the $30 blades.

Edited by Pete Staehling

I agree with Pete.  Dull blade. 

I tried both a Resaw King, and a Trimaster on my 14" saw.  I didn't see much difference in cut quality, but the RS was a bit more finicky with demanding the just right tension.  The Trimaster is a bit thicker, and not as demanding on tension.  It requires more tension, but anything above the amount needed seems okay too.  I bought a 24" saw, and sold both 105" resaw blades, since they would never get used here again.

It depends on how much sawing you need to do.  A Timberwolf blade will stay useable for about 20 minutes of cutting in soft wood.  Carbide tipped will last for days.

 

You didn't tell us how many TPI your blade has.  Resaw requires a low TPI, ideally 3 or 4.

Another possibility is your saw just isn't tuned right.  Out of square table, drift issues, improper tension, incorrect placement of blade on upper wheel, guide bearings (or blocks) not set right, etc.  There are a lot of finicky adjustments on a bandsaw and if just one of them is off, resaw will not go well.

Or it could be the blade is just crap.  I know TC had nothing but bad things to say about some Laguna blades he was using.  I find it hard to believe they're THAT bad, but I'm pretty sure he knows how to tune a bandsaw.  So who knows.  Check TPI first, then make sure the saw is properly tuned, then look into a new blade.

Are we sure your bandsaw is setup correctly? Did you watch the video from Alex snodgrass (I think is how you spell his last name) before you started?

  • Author

You didn't tell us how many TPI your blade has.  Resaw requires a low TPI, ideally 3 or 4.

Another possibility is your saw just isn't tuned right.  Out of square table, drift issues, improper tension, incorrect placement of blade on upper wheel, guide bearings (or blocks) not set right, etc.  There are a lot of finicky adjustments on a bandsaw and if just one of them is off, resaw will not go well.

Or it could be the blade is just crap.  I know TC had nothing but bad things to say about some Laguna blades he was using.  I find it hard to believe they're THAT bad, but I'm pretty sure he knows how to tune a bandsaw.  So who knows.  Check TPI first, then make sure the saw is properly tuned, then look into a new blade.

Correction - It's a Laguna Shearforce 5/8 " blade, not 3/4. It's 3-4 TPI Variable. I've only used the blade 5 or 6 times, certainly it's not dull. One other thing of note, the teeth are all 'gummy' after resawing, not sure this is just from the heat build up or something else.

 I setup the saw when i first bought it but will go through it all again to make sure it's not a setup issue.

Looking at a high-end resaw blade is the same as looking at a high-end blade for any other tool...

For example, purchasing a Forrest WWII won't get you a glue-line-rip if you're currently burning stock on table saw rips -- you've got to adjust the fence first to get a clean cut, then start looking for that glue-line-rip...

So,

On a saw that's already resawing well, a high-end blade will [probably] improve the results...

On a saw that's not resawing well, you've got to tune it in first before looking to refine the results with a fancy blade....

Edited by hhh

  • Author

Are we sure your bandsaw is setup correctly? Did you watch the video from Alex snodgrass (I think is how you spell his last name) before you started?

I had not watched Alex's video, but had watched 2 or 3 others. Not even 10 minutes in and I've learned two new things! Thanks for sharing. For others, here's the link:

https://www.youtube.com/watch?v=wGbZqWac0jU

I run a 3/4 wood slicer blade from highland and have been very happy with.  Very reasonably priced as well..   Certainly another option after your saw is dialed in.

I have a 1/2" Woodslicer and a 3/4" Resaw King for my 14-12 and both blades have worked great, it sounds like there may be an issue with the blade you have. 

I've been on the fence about the RK for a long time so I've given it a lot of thought.

The only justification I can think of to buy the RK is if you work with very expensive species and you want to cut them into veneers, or if you don't have a drum sander.  I'm fine with a regular blade like a Timberwolf if I'm just trying to resaw say a cherry or a walnut board...I just take them straight to the drum sander afterward and I don't worry about the waste that's caused by the somewhat rough cut.  But if I had a piece of higly figured koazilian rosebolo that I paid 100 beans per board foot for, then I'd wanna maximize the yield obviously.

Once you factor in the cost of the RK and the cost of the sharpenings, you better have some primo sticks you're planning to work with or I think it's just money down the toilet.

I just cut some veneers from cherry and walnut with a relatively cheap/inexpensive (~$15) 4 TPI ⅝" blade on my 17" Grizzly bandsaw.  I get them made up at a local tool store.

The cut was a bit rough but a bunch of light passes on a drum sander and the veneers are great.

However, I am looking to get a better quality re-saw specific blade to try.

Edited by ChrisG-Canada

Noob, I had the same issue with my 1412 and that laguna blade. There isn't enough set in the teeth for the cut to clear the way for the back of the blade. That's why you're getting the burning. It cut great for about 5 linear feet and then it burnt everything and cut quality when right down the crapper. 

I bought a Starret 4 TPI hook tooth blade for 20ish bucks at woodcraft,cuts great. Here's a video of that starrett blade cutting some hard maple.

 

My Laguna 14 12 has resawn many many feet of various woods from myrtlewood to pine with no problem. I am using a 3/4" 4 tpi blade! Very happy with it so far.

  • Author

Noob, I had the same issue with my 1412 and that laguna blade. There isn't enough set in the teeth for the cut to clear the way for the back of the blade. That's why you're getting the burning. It cut great for about 5 linear feet and then it burnt everything and cut quality when right down the crapper. 

I bought a Starret 4 TPI hook tooth blade for 20ish bucks at woodcraft,cuts great. Here's a video of that starrett blade cutting some hard maple.

 

Thanks, I was certainly hoping it wasn't just my amateurness. LOL.

I spent a hour last night trying to setup it up following the Snodgrass method but still had sh*tty results. It burned and the blade tracked to the right after the first 2 inches of the cut.

I'm fortunate (fortunate in convince, certainly not to my wallet) to have a Woodcraft 10 min from my house. I'll stop by there on my way home. 

  • Author

oh man! Got my saw setup and using the Starrett blade, wow what a difference. I'm sure part of the original problem was my setup, but boy that Laguna blade was so they should be ashamed to sell it. The Starrett blade cut through 4 in ash like butter. Thanks for the help guys!

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,011 Total Members
  • 3,644 Most Online
  • bobtjanitor Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.