miranthis Posted January 2, 2016 Report Posted January 2, 2016 The original switch in my TS just shorted out. It is one of the box type switches that screws to the bottom of the TS table and you plug the motor into it. Opened it up and it had vibrated over the last 48 years, through the insulation and arced (see pic below). The usual suspects (Rockler, Woodcraft, amazon, etc) all have 15A accessory switches (the big stop paddle type), but no 20 amp version. My TS motor is only a 1 hp Craftsman Tool Motor, but it says to use a 20 amp circuit in the manual. Anyone have any ideas? Jeff in KC Quote
..Kev Posted January 2, 2016 Report Posted January 2, 2016 Grizzly carries switches, you might have a look there to see? Or.. After 48 years, you could replace the saw? Welcome to the forums! Quote
wtnhighlander Posted January 2, 2016 Report Posted January 2, 2016 Good time to look into a magnetic safety switch, that prevents the saw from restarting on its own after power loss. Quote
miranthis Posted January 2, 2016 Author Report Posted January 2, 2016 19 minutes ago, TIODS said: Grizzly carries switches, you might have a look there to see? Or.. After 48 years, you could replace the saw? Welcome to the forums! Them is fightin' words.....:-) I'll replace the saw when it is worn out, and not before.....:-) Besides, my granddad, who I got it from, made a lot better stuff than I am making, all with that saw. If he can do it, I can too. Nope, the lazy way is to just buy a new saw instead of learning to use the one I have. Besides, why trash a perfectly good saw for want of a switch. This one is really just getting broken in....:-) In the meantime, I will check Grizzly and ebay....if it had not melted the tab I would just have rewired it....:-) Quote
Tpt life Posted January 2, 2016 Report Posted January 2, 2016 Woodstock D4151 110/220-Volt Paddle Switch https://www.amazon.com/dp/B005W17FRS/ref=cm_sw_r_cp_awd_ShgIwb5H2YA5K Prime. Have it Monday. Quote
wtnhighlander Posted January 2, 2016 Report Posted January 2, 2016 Or how about this? http://www.amazon.com/gp/aw/d/B005W17FRS/ref=pd_aw_sim_sbs_469_1?ie=UTF8&dpID=41oo%2BSPeL2L&dpSrc=sims&preST=_AC_UL100_SR100%2C100_&refRID=0DBRH2YMZ6EDWH1ZRPBH Quote
Eric. Posted January 3, 2016 Report Posted January 3, 2016 32 minutes ago, miranthis said: Them is fightin' words.....:-) I'll replace the saw when it is worn out, and not before.....:-) Well technically it'll never actually wear out if you keep replacing all the parts that go bad. It's not like it's gonna spontaneously implode on you in an instant some day. Old tools are great if you like tool maintenance. But there have been some nice upgrades made to table saws in the last half century that pretty much justifies the purchase if you did buy a new one. I'm not trying to talk you into anything because I truly don't care what saw you have in your shop...but there are good arguments for joining the 21st Century. Riving knife first and foremost. I'd trade in any old saw for a new saw with a riving knife. Better fences would be number two. Quote
Popular Post miranthis Posted January 3, 2016 Author Popular Post Report Posted January 3, 2016 Ok, I downloaded the 1967 Craftsman catalog and that switch that has been on there since 1967 is a 15 amp switch, despite the motor manual saying that it should be used on a 20 amp fused circuit. It was sold to go with the 1 hp tool motor, so I will just replace it with the new 15 amp switch. That having been said, the switch I am replacing looks a lot like this one, just the 1967 model....its a full enclosed switch with a place to plug the motor in and a cord running out of it to the wall.....I should have been more specific that i needed the whole thing, nit just the toggle itself.http://www.woodcraft.com/product/145199/woodriver-accessory-power-switch.aspx Thanks for the help. 16 minutes ago, Eric. said: Well technically it'll never actually wear out if you keep replacing all the parts that go bad. It's not like it's gonna spontaneously implode on you in an instant some day. Old tools are great if you like tool maintenance. But there have been some nice upgrades made to table saws in the last half century that pretty much justifies the purchase if you did buy a new one. I'm not trying to talk you into anything because I truly don't care what saw you have in your shop...but there are good arguments for joining the 21st Century. Riving knife first and foremost. I'd trade in any old saw for a new saw with a riving knife. Better fences would be number two. Hope you saw the smiley face. Seriously though, I am very happy with the saw. I prefer the old to the new on this. I may get a cabinet saw one day (when my shop is not just 1/3 of a 3 car garage), but for now I'll keep using the saw used to make the crib I slept in as an infant. :-) Every time I use it I think of my granddad, and that is worth more than a new saw to me. Besides, if i can't do it with my 1967 Craftsman, I don't need to be doing it. :-) Jeff in KC 4 Quote
..Kev Posted January 3, 2016 Report Posted January 3, 2016 You can add a splitter in a 0 clearance insert which would help on the safety front. I think MJ splitter makes them, someone correct me if I got that name wrong. Quote
miranthis Posted January 3, 2016 Author Report Posted January 3, 2016 1 hour ago, TIODS said: You can add a splitter in a 0 clearance insert which would help on the safety front. I think MJ splitter makes them, someone correct me if I got that name wrong. got them both, but I do like the original blade guard when that works for my cut. I also have a dedicated 45 degree Zero Clearance insert, both the inserts have provisions for use of the blade guard. I also enjoy my original rip fence....makes me measure twice :-) Over the years I have added PALS, the red drive belt and a few other conveniences. 1 Quote
miranthis Posted January 4, 2016 Author Report Posted January 4, 2016 OK, i replaced the switch and redid some cuts that had been giving me trouble. Motor did not cut out, trip the breaker or even heat up. No bogging down on the 45 degree rips of 3/4 ply. Maybe its just me, but that switch had been failing for a good long while and now that I have the power supply cleaned up it is working much better......or I am just imagining it. Either way I like the results. Jeff in KC Quote
Phil B Posted January 4, 2016 Report Posted January 4, 2016 Plus +100 on the magnetic switch. It's a very good safety upgrade. It would be a bad thing for the power go off in the middle of cutting something. It would be a lot worse if the saw started up when the power comes back, making for a potentially hazardous situation. Griz has a lot of choices. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.