Recommended Posts

Posted

I need some fresh ideas on some drawer slides. 

I made these and thought I had it all figured out how to make the proper way on paper, once I got them built I changed my mind. Now I am having troubles with a proper slide. 

any thoughts would be greatly appreciated.

IMG_20160131_185931.jpg

this is the pattern of the drawer

IMG_20160131_190027.jpg

IMG_20160131_190013.jpg

The middle is a cookie sheet drawer, had a under mount roller system but one I gave it a test run it failed so need to figure that one out as well.

I should mention 90 degree from center of face frame is 11 inches. 

  • Like 1
Posted
thanks but as the nickname says. would you mind explaining the web frames or post a picture?

No problem! Here is a link to the chest of drawers guild build I did last year. I documented most steps. Have a look through it and it and if you have any other questions I'd be glad to help you.

http://www.woodtalkonline.com/index.php?/topic/18942-Chest-of-drawers

Chest of drawers

Sent from my SM-N910W8 using Tapatalk

Posted

If you don't mind me asking, how much do you have in the cost of wood? I love Purple Heart wood and know it's not that cheap. Seeing a large project like that makes me curious on total costs. And how did you connect the joints? I made a shadow box out of Purple Heart wood and every time I tried a brad or nail, it split down to the end. Had to use splines to connect corners

Sent from my iPhone using Tapatalk

Posted

Hi amateur eric 

I am not 100% sure I am going to guess about 600.00 in the Purpleheart I get a pretty good deal on it at 11.00/bf for rough lumber. I mill everything to size. This is the second section I have built, I have one hanging cabinet made as well. I have been attaching everything by pocket screw. Put it all together and then would have a split when screwing so I know your pain. I finally came to the conclusion I have to predrill everything. I drill the pockets and then assemble, clamp and then run the screw through the pocket so I have a set for the drill bit and then drill them on the press drill. I have the degree written in felt marker inside my Kreg kit. I also use a nail set on any other holes (hinges) to keep the bit from drifting. On the angled piece I used biscuits and glue, this worked out quite nice as i was able to round the joint with sanding so it has a rounded edge and looks clean. I have tried the fine dust and glue for filler but have yet to make anything that come even close to matching so I gave up and I now make sure my saws are perfectly square before I start cutting, being it is so hard it fits together quite clean if perfectly square.

My background is more working with metal than wood until my wife asked me to build her new cabinets so I treat the wood exactly as I would with metal, screw holes must be just (a blonde c hair....hehehehe) smaller than the screws, the standard "same size as screw shaft" isn't quite big enough, but once in they really hold and I never use a cordless drill, I have a 4 volt Ryobi screwdriver that I use, it will stall out before it will spit the wood, then I hand tighten

If you are considering a bigger project like this this make sure you buy a can of blade coat, I bought a new Dewalt planer and after about 5 board feet the rollers wouldn't push the wood through (I only increase 1/3 of a turn at a time), I was just about to take it back when the thought crossed my mind and I took it apart and sprayed the blades, works like a charm now, I spray every blade or bit before I start doing anything and it helps immensely.  

Pic of the other ones and yes once I get these finished the bread box is next. I have to do a set of walnut doors for another house so the last 2 sections will get put on hold until I am done those (I have a patient wife). I am also going to try a set of raised panel doors for under the kitchen sink but I am procrastinating on those as my other doors are a miter joint and I haven't figured out how to put them together yet. I can honestly say I am having fun working with this wood.

IMG_20160202_192637.jpg

  • Like 1
Posted

Working with Purpleheart 1/3 of a turn is way more than I'd go. At most I'd do like an 1/8th turn and slowly remove material. I must be in a good location because my local dealer sells PH for $8.50. I pay higher than usual prices for oak and maple though at $4 &$4.50 respectively.

PH also takes glue as well as any other wood in my experience.

Posted

Hi Chestnut,

I am near Calgary AB and typically us Canadians pay more for everything.

I agree with you about the glue.

Going 1/3 doesn't seem to drag the motor down and they are coming out almost perfectly smooth (I did a water test on one of the drawer pulls and there was absolutely no running - I was actually more amazed that my work table was that level), quick 220 sanding and they are ready to be shaped. I sand them quick after to keep the slivers down as I hate wearing gloves. I am going to assume that once my blades get duller I will have to shorten the cut.

Posted

@Still learning Ahhh yeah the Canada factor. I'm very familiar with things being more expensive up there. Living near the boarder to Winipeg we get a lot of northerners that run down for cheaper goods. Alcohol seems to be crazy expensive up there. The curlers i run into buy as much as they can before they head home.

Cabinets look great. Honestly i'd been nervous to make cabinets from purpleheart, that's a lot of purple for me. I do love the grain and luster of the wood though. I have some stuff that turned brown and almost enjoy (looks) it more than walnut.

Posted

Thanks, we love the color and like to be different, the kitchen is on the north side of the house and doesn't get any direct sunlight and the change will be slow, I think one day we will be eating supper and notice they changed but we all like change after a while.

I probably leaned towards the purple heart as it doesn't need staining and I suck at finishing, was always at the bottom of the class in art.......... and I can't afford to get anyone to finish, you want to talk about expensive, looked into it.

3 hours ago, Chestnut said:

PH also takes glue as well as any other wood in my experience.

What is the thinnest a person could go for a panel and still get a decent glue up? I have been thinking of making inserts instead of the raised panel. I originally looked into a veneer but wasn't happy with the color match.

  • 4 weeks later...
Posted

Hi All,

I finally put my mind to this and got them in and 90% completed, just have to fine tune.

I eventually went with a 2" side mount and mounted them underneath the drawer with Maple on the bottom of the drawer so I could screw into and walnut as the main holder for the slide, which is bolted through and are placed in length to the back/side at a 45 angle, I am truly glad I did it this way as there is enough adjustment to get it all set. I hung the pulls on them today and they are going to be able to take the weight. To allow removal I made the drawers with 1/4 to 1/8 inch clearance at the top and now realized can go a bit tighter.

Would I be better to go with a teflon slider as apposed to a piece of oiled maple? This would be attached to the to bottom of the face frame.

Drawers are made of pine and painted white.

Posted

If your doing wood sliders I'd keep it hardwood on hardwood. I've had good luck using a hard finish and then waxing them. You could even leave one unfinished and just use wax on the unfinished wood. Another option would be UHMW tape. Can buy it at various places, any route you go I'd still suggest wax to cut down on the amount of wear you will get. Depending on use it wouldn't have to be refreshed that often.

Posted

Thanks Chestnut, I have a hunk of pure bees wax, would that work? 

Pic so you understand what I did.

My center of gravity is about 1/2 inch short so I am using the long side to the face frame as the stable running slide.

I know it is unorthodox how I did it, only requirement my wife had is they open easy, to which they do.

IMG_20160229_163245_hdr.jpg

Posted

I was thinking paste wax. Never used bee's wax. I've heard of paraffin wax being used but i think the point is something hard that doesn't gum up. I use paste wax for a ton of different things.

5d19e489-b88b-43e4-900f-57133702d8eb_400

 

Posted

Thanks Chestnut, 

I did some online reading and I think I am going to try the bees wax just because I have it and love to experiment. 

Once again thanks for the wax tip, that one didn't even cross my mind.

Posted

I'm not sure, as I've never done it, but I would think the bees wax will stay soft and gooey and the paste wax (Minwax or Johnsons) will get hard and slick. "Hard and slick" is better for your drawer slides.

The reason I say bees wax is soft is that I use it once in a while from a toilet ring that I keep handy for driving screws into harder wood.. The wax that I have is still soft after about 6 years of sitting on the shelf covered in wax paper to keep the dust off of it.

My Minwax is the wax that I go to for a finish on projects and it sits up and hardens and makes for a nice smooth surface when polished up.

But, who knows it may work just fine.

 

Posted

Thanks Rapid Roger,

The block I have is really hard, I would have to melt the whole thing to work with it as I don't think I could safely cut it. Bought it at a farmers market last summer for some reason and now it has a purpose. My father in law was a beekeeper most of his life   and my wife is a master at liquefying honey.

I read a couple recipes online and am going to experiment with all and see which one is the best. I didn't know what I was doing when I started so a few more learning mistakes won't matter.

Posted

I have used bees wax on bedroom furniture and it worked excellent. It takes a bit to get the right amount of a coating but it last for a long time and very easy to apply.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Who's Online   1 Member, 0 Anonymous, 53 Guests (See full list)

  • Forum Statistics

    32.1k
    Total Topics
    437.6k
    Total Posts
  • Member Statistics

    26,009
    Total Members
    3,644
    Most Online
    Joseph b
    Newest Member
    Joseph b
    Joined