davestanton Posted February 20, 2016 Report Posted February 20, 2016 These are nearly 200 years old and work very well. Interested to know how many of you guys still use these? Quote
James Wright Posted February 20, 2016 Report Posted February 20, 2016 I use them regularly. I have an almost complete set. And to your question they are always bevel down. The tang of theach iron stays in the channel. 1 Quote
Tony Wilkins Posted February 20, 2016 Report Posted February 20, 2016 I really want some and would definitely use them if I had some. Quote
Tom King Posted February 20, 2016 Report Posted February 20, 2016 I use mine more than I ever thought I would. Quote
sjk Posted February 21, 2016 Report Posted February 21, 2016 If I could find any that weren't $$$$, I'd be giving them a try in my workflow. Quote
Coop Posted February 21, 2016 Report Posted February 21, 2016 I'm amazed at how very little wood there is on the side that supports it. I would think that driving/tapping the wedge in to tighten the blade, would spread the gap and cause it to not be straight or to snap it in half? Quote
Tom King Posted February 21, 2016 Report Posted February 21, 2016 Mine all came from the UK, off ebay, for average price less than twenty bucks a piece. Then, shipping for a small packet was about eight bucks. I'm not sure what it is now. I've had the best luck with molding planes from the UK. It seems like they took care of them over there, whereas here they ended up in barns rusting and splitting. I didn't buy any that had rusty, much less pitted, irons. I didn't care a bit about a matched set. I just wanted ones I could use. The best prices came from people who named them the wrong thing, like pristine snipes bill, and half rounds that were called something else, and buyers didn't notice them. 1 Quote
TerryMcK Posted February 21, 2016 Report Posted February 21, 2016 I normally see them for sale as "Old wood planes" where the seller hasn't a clue what they are apart from old. The prices are really low over here too. Although the prices are steadily increasing as popularity for such tools is also on the rise. I recently picked up a set of 21 mixed molders - some of them matched hollows/rounds - for £60 (about $86 US). As they appear on sale cheaply I'm adding more. On another UK website I saw a 14 set of hollows and rounds frome the 1850s for £280 (over $400 US) so the prices are widely differing. 5 hours ago, K Cooper said: I'm amazed at how very little wood there is on the side that supports it. I would think that driving/tapping the wedge in to tighten the blade, would spread the gap and cause it to not be straight or to snap it in half? Some of the molders I own have less than 1/4" wall but the wedge action doesn't force the sides apart as the wedge is parallel sided. It applies force onto the blade only and this force is transmitted to the thickess portion (top to bottom) of the plane body. I have remade wedges as the original ones had been butchered up by somebody using the wrong method to try and extract it. They had used a hammer to pound onto the rounded nub cut into the wedge instead of tapping the back of the plane body to loosen it. The nub is then used to grip the wedge so it can be pulled out. 1 Quote
Gilgaron Posted February 22, 2016 Report Posted February 22, 2016 On 2/21/2016 at 7:42 PM, sjk said: If I could find any that weren't $$$$, I'd be giving them a try in my workflow. Lee Valley has these: http://www.leevalley.com/en/Wood/page.aspx?p=64009&cat=1,41182 I have two pair I've been playing with. They are rather small and I believe the $$$$ side escapement planes are supposed to work better, but they worked well for a few small things I've tried them with. The fiddliest thing was getting the wedge to stay in. They're my only wooden planes and I'm used to being able to take heavier cuts by pushing harder with my iron planes. Quote
sjk Posted February 23, 2016 Report Posted February 23, 2016 Thanks @Gilgaron. I've been thinking of getting a pair of those to try out - it's good to hear the opinions of someone who has them. Quote
Gilgaron Posted February 23, 2016 Report Posted February 23, 2016 Yeah I read Bickford's book on using hollows and rounds and then got them, since they are an order of magnitude less than new H&Rs and I didn't feel like learning to fettle wooden planes. Since they are so small (about as long as my hand) you definitely need to do like the book says and have them ride in rabbets, grooves, and chamfers. So a combo/plow plane and a rabbet are necessary companions whereas I could see the bigger Western style planes maybe being more forgiving. He talks about wooden plows and rabbets in the book but I just use a Sargent 1018 and Stanley 78 and it works just fine. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.