collinb Posted February 27, 2016 Report Posted February 27, 2016 But most of all, teach them how to correctly and safely use tools like this. This guy is seriously heading for digit damage or loss. btdt. Quote
wtnhighlander Posted February 27, 2016 Report Posted February 27, 2016 I see that I would be using a push stick. 1 Quote
JosephThomas Posted February 27, 2016 Report Posted February 27, 2016 He was probably about to reach for a push stick 2 microseconds after the pic was taken. Relax. Quote
Brendon_t Posted February 27, 2016 Report Posted February 27, 2016 2 hours ago, Mike. said: Why? I don't see anything wrong. Not sure if this is sarcastic but I actually don't. How his right hand has fingers locked over the fence is how I work. I'll just remove the other hand a few inches early. 1 Quote
Popular Post Coop Posted February 27, 2016 Popular Post Report Posted February 27, 2016 Aside from a serious imbalance of ink from one side to the other, I don't see a problem. In fact, if you beef up those biceps about 50%, that very well could be me in that pic? 3 Quote
Eric. Posted February 27, 2016 Report Posted February 27, 2016 Yeah I agree. No huge red flags in that pic for me except the splitter. I don't stand directly behind the board unless I have to, but I hook my right hand fingers just like that and use my left as a featherboard constantly. He's fine unless he just pushes his hot dogs straight through the blade...and that would be a mental error (complete brain malfunction) and not a technique issue. Quote
Gixxerjoe04 Posted February 27, 2016 Report Posted February 27, 2016 Well if he pushes it through with his hand and I dont see a riving knife or anything, if that happens after the pic then yea, good way to lose some fingers. But i push all my cuts like that but finish with my gripper. He has tattoos and safety glasses, he's good. 1 Quote
Immortan D Posted February 27, 2016 Report Posted February 27, 2016 Give or take a few pounds, that guy could be Eric. Quote
Brendon_t Posted February 27, 2016 Report Posted February 27, 2016 25 minutes ago, K Cooper said: In fact, if you beef up those biceps about 50%, that very well could be me in that pic? I was thinking that was your older brother. Quote
Eric. Posted February 27, 2016 Report Posted February 27, 2016 Yeah and give or take all of the tattoos too. As in take. But he does have a beard and that semi-pissed off look on his face. 1 Quote
Immortan D Posted February 27, 2016 Report Posted February 27, 2016 Just now, Eric. said: Yeah and give or take all of the tattoos too. As in take. But he does have a beard and that semi-pissed off look on his face. hmmm I was referring to ET... Quote
Eric. Posted February 27, 2016 Report Posted February 27, 2016 Then you should have said ET. Because he's not Eric, I'm Eric. LOL Quote
Brendon_t Posted February 27, 2016 Report Posted February 27, 2016 Candy is a stripper name. I'm fairly certain you don't want me stripping, unless you're into hairy fat guys. . Quote
Immortan D Posted February 27, 2016 Report Posted February 27, 2016 Well you posted a pic of your stripper pole a while ago. Quote
Immortan D Posted February 27, 2016 Report Posted February 27, 2016 Because they change their names to Portia once they get their degrees. 1 Quote
collinb Posted February 27, 2016 Author Report Posted February 27, 2016 Why? I don't see anything wrong. Not sure if this is sarcastic but I actually don't. How his right hand has fingers locked over the fence is how I work. I'll just remove the other hand a few inches early. To those who see nothing wrong, this is how my injury happened. I kept my fingers at a safe distance ... until the blade hit a hard spot in the wood and it jumped, throwing my thumb into the blade. Just enough damage for an er trip, but fortunately no serious damage. Just enough to buy a Grripper. Sent from my MotoE2(4G-LTE) using Tapatalk And I was also using my left hand like a feather board. That's what jumped. Sent from my MotoE2(4G-LTE) using Tapatalk Quote
Brendon_t Posted February 27, 2016 Report Posted February 27, 2016 I'm my experience, a steady light forward pressure is all you should have to give the wood while pushing through a saw. If you're pushing hard enough that your hand jumps forward, there's something else wrong. I'm sorry you were injured but I'd bet if you had instant replay, you would likely find the actual root problem. IMO saying his hands feeding position is unsafe is just fear mongering. Quote
Eric. Posted February 28, 2016 Report Posted February 28, 2016 I guess I should clarify that when I say I use my left hand as a featherboard, my hand is PLANTED on the table and it is only being used to apply lateral pressure into the fence. My hand does NOT move along with the board toward the blade. So if there did happen to be any sudden movement (which there isn't because I only put flat and square stock on my table saw and I use sharp blades), my hands would still not be in the path of the blade. Upon further inspection of the picture above, it does appear that homeboy's left hand is moving toward the blade with the board, and I do not recommend doing that. Ever. Quote
Immortan D Posted February 28, 2016 Report Posted February 28, 2016 That saw is not running. I can see the teeth on that blade. It's a Zoolander type of pic, not part of any woodworking master class... Quote
Coop Posted February 28, 2016 Report Posted February 28, 2016 7 minutes ago, Eric. said: Upon further inspection of the picture above, it does appear that homeboy's left hand is moving toward the blade with the board, and I do not recommend doing that. Ever. And what if you are ripping several boards from the one and the board to the left of the blade will go against the fence on the next cut. Not following thru with the left hand will leave a titt on the end of the board. Not contradicting, just wondering why you don't follow thru with the left piece if there is sufficient distance from the blade? Quote
Eric. Posted February 28, 2016 Report Posted February 28, 2016 12 hours ago, K Cooper said: And what if you are ripping several boards from the one and the board to the left of the blade will go against the fence on the next cut. Not following thru with the left hand will leave a titt on the end of the board. Not contradicting, just wondering why you don't follow thru with the left piece if there is sufficient distance from the blade? If there is sufficient distance from the blade then it's a different story. When your hand is in line with the blade, you don't. Two different scenarios. Also I find that if you push the board through at a moderate feed rate, you aren't usually left with a "titt." Either way, you can knock it off with a block plane or go back to the jointer so you have a nice flat edge to go against the fence. The "titt" is of little concern to me; my fingers take precedence. Quote
wtnhighlander Posted February 28, 2016 Report Posted February 28, 2016 I used my push block EVERY time. Not just because it is safer, it also keeps downward pressure across a larger area, giving me a better cut. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.