Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Flip-top cart fail

Featured Replies

In an effort to make as much use out of a small workshop as possible, I attempted to build a flip-top work cart for my planer and a future tool, perhaps the Ridgid oscillating sander that many speak well of.

I tried to follow a plan from a FWW article that has the notches on the four corners of the top and a 1" dowel shoved in 3" on each side. When I tested it without weight, it seemed to work OK, except if the knobs aren't completely tight, it wobbles a bit. 

However, once I mounted the planer, yuck. It flips ok, but there is no way to get the notches lined up so the eye bolts go into the notches. I'm trying to figure out if it's just a weight issue or if I should just rebuild the top using a dowel that runs all the way through, hopefully ensuring the alignment is better. 

Anyone build one flawlessly the first time out, or have a similar issue?

Any play or wiggle in the flip axis will cause the pin not to fit. Axis/axle  should be rather stiff fitting and not turn very easily. You could taper the pins so they wedge in place. Adding a bolt w a wing nut & lockwasher would keep it from vibrating loose while using the planer.

The Ridgid oscillating belt/spindle sander is a great little tool. After several years of abuse in my cabinet shop I killed my first one. Pushed it too hard 3 days in a row and burned up the motor. Went right out and got another one !

I've built two flip top stands, one for my Planer/Sander, the other for my Miter Saw/Mortiser. Both of mine have a steel rod passing all the way through, 3/8th smooth for the Planer, 5/8th threaded for the Miter Saw. They stay very even in this configuration, with the tools bolted through the top.

The wood dowel only passing 3" into the top concerns me. I wasn't able to find any references to this cabinet design online. How is the top mounted to the pivots? For reference, my tops are two pieces of 3/4" Plywood laminated together, with the rods epoxied into a routed slot in the center.

  • Author

Thanks for the replies. 

The top is basically two pieces of plywood with 3/4 hardwood framed on the inside. The corners have the notches in the hardwood to hold the eye bolts that go in and out to fasten to the sides. The dowel pieces are centered on the sides and line up with the notches, then driven in about three inches and cut off flush with the sides. 

The plan is from Shop Notes, not FWW.

image.jpeg

" They won't stay in their little storage pockets when it is upside down." 

Deduction or experience ? I can picture sleeves , washers, wrench etc flying out during the flip !

2 hours ago, wtnhighlander said:

Deduction, since they barely stay in place sitting still!

?

I'm pretty sure the slots they are stored in are spring loaded.  I don't think I've ever touched my sander without at least one of the sleeves or washers leaping out and falling behind something.

I built a flip top stand for my planer and ridgid sander. It's two pieces of 3/4 in plywood with a half in steel rod down the middle. The rotation is stopped using two slide-type bathroom door locks (I'm sure there's a better name). The problem I ran into was the rod was too short, so the walls bowed and the platform would fall. The solution was to add a fender washer and then lock it in place by jb welding a copper plumbing coupler and a cotter pin. So far it's holding. And yes, I added a drawer at the bottom (though not a good one. First time making a drawer.) 7f5be5ff5b7457172e336634bf6dda49.jpg

aa42f711d272b73a1ac6258de48e482f.jpg

That sounds right. Thanks. I forgot I added brass bushings on the inside face so the plywood wouldn't wear out.

Sent from my SM-G900T using Tapatalk

  • Author

I'm going to tear it down and start over after I finish the miter stand cart I'm building now. The non-flip-top stand works fine as a stand for my DW734. I'll report back, hopefully with a functional one, lol. 

  • 2 weeks later...
On 3/7/2016 at 4:49 PM, jplemons said:

The plan is from Shop Notes, not FWW.

That is similar to the one I built so I obviously saw the Shop Notes article at some point . . .  I added pivot block supports to fatten up the support area for the 1" oak dowels I used for axles. 

I had many different tools on this till I handed it down to my dad.  He now has a DW735 planer and the Ridgid belt/spindle sander on it as you describe.  It has been in service since around 2009.

You can see I made one side removable in order to add t-nuts for different tools over time.  Amazingly, this was an idea that actually paid off :D

 

Flip-top 3.jpg

fliptop-2009 flipping.jpg

fliptop-2009 lock removable top surface.jpg

1 hour ago, gee-dub said:

That is similar to the one I built so I obviously saw the Shop Notes article at some point . . .  I added pivot block supports to fatten up the support area for the 1" oak dowels I used for axles. 

I had many different tools on this till I handed it down to my dad.  He now has a DW735 planer and the Ridgid belt/spindle sander on it as you describe.  It has been in service since around 2009.

You can see I made one side removable in order to add t-nuts for different tools over time.  Amazingly, this was an idea that actually paid off :D

 

Flip-top 3.jpg

fliptop-2009 flipping.jpg

fliptop-2009 lock removable top surface.jpg

Very Nice. I'm seriously considering building one of these for the planer/ oss.

And that looks like a dw734.

On March 27, 2016 at 8:27 AM, Brendon_t said:

Very Nice. I'm seriously considering building one of these for the planer/ oss.

And that looks like a dw734.

Yes, I had a DW734 and a belt/disc combo on it, I also had a CMS on it for a while and then the rigid OSS. When it moved on down to dads he put his DW735 on it, and I let him keep the OSS :-)

It was certainly one of the more beneficial fixtures I have ever built for my shop.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,009 Total Members
  • 3,644 Most Online
  • Joseph b Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.