Brendon_t Posted March 8, 2016 Report Posted March 8, 2016 I'm pretty sure I have shot the bearings in my router to smithereens. Upon initial startup, there is some nasty vibration until the bit gets up to speed. I'm sure the deep handheld routing on the bench didn't help much either. Router in question is a 2.5hp craftsman. Is replacing bearings on a router even worth it? Quote
wdwerker Posted March 8, 2016 Report Posted March 8, 2016 Bearings don't cost that much but on some routers it is quite a chore to get it apart, replace them and then get it back together in running order. I have done it on several PC690 routers and a few PC HD laminate trimmers (the fat heavy powerful ones they don't make anymore). The older style Bosch laminate trimmers weren't worth the fight. If you are a decent mechanic and snap rings, e clips, wires and such don't pose a barrier you could give it a whirl. Like I said bearings aren't that expensive if you can find the right size. Quote
Brendon_t Posted March 8, 2016 Author Report Posted March 8, 2016 Thanks Steve. On that info, I just went out and pulled it apart. Super easy. Took 15 minutes to pull the bearings and reassemble. It takes a common 6004RS bearing. Now if I can only remember what trip said about z ratings and sealing codes. Quote
Brendon_t Posted March 9, 2016 Author Report Posted March 9, 2016 34 minutes ago, wdwerker said: use the search button! That's not as fun as attempting to home my instant recall. . 1 Quote
wdwerker Posted March 9, 2016 Report Posted March 9, 2016 " That's not as fun as attempting to hone my instant recall " There, fixed it for ya ! Quote
Coop Posted March 9, 2016 Report Posted March 9, 2016 Who Ya gonna talk into to make that first cut once you get it back together? Quote
wdwerker Posted March 9, 2016 Report Posted March 9, 2016 Clamp the router in the vise unplugged. Put a straight bit in it and plug it into an extension cord. Lock the switch/ trigger on, then cross the room and plug in the cord. Quote
wtnhighlander Posted March 9, 2016 Report Posted March 9, 2016 Or go in the other room and close the breaker! ? Quote
Brendon_t Posted March 9, 2016 Author Report Posted March 9, 2016 2 hours ago, K Cooper said: Who Ya gonna talk into to make that first cut once you get it back together? Isn't that why people have kids? Quote
wdwerker Posted March 9, 2016 Report Posted March 9, 2016 They would be a smaller target if the thing decides to come apart. Quote
TerryMcK Posted March 9, 2016 Report Posted March 9, 2016 6 hours ago, K Cooper said: Who Ya gonna talk into to make that first cut once you get it back together? I used to know an electrician who after doing a job like installing a light switch would ask somebody else to try it out. He used to close his eyes and look away while the victim tried it out. Quote
Chestnut Posted March 9, 2016 Report Posted March 9, 2016 Do it. I rebuilt an engine with little previous experience and it's running like a champ. Just take things slow and double check your work. If you do install some thing wrong i doubt there would be a huge spectacular failure it probably just wouldn't spin up or will wobble. Quote
Brendon_t Posted March 9, 2016 Author Report Posted March 9, 2016 After tearing it down, it's super simple. The I was expecting the r&r to be a bit more complex. I'll give it to craftsman, they made it simple and intuitive to break down Quote
Chestnut Posted March 9, 2016 Report Posted March 9, 2016 Did you take some pictures it'd be interesting to see what the guts look like. Quote
Brendon_t Posted March 9, 2016 Author Report Posted March 9, 2016 I did not. Ordered the parts via prime. Which will arrive tomorrow. I'll take a few disassembly pics when I tear it back open. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.