duckkisser Posted March 12, 2016 Report Posted March 12, 2016 im looking to update my router in my router table (old router is a pain to adjust depth as its just a plunge router no micro adjust. I was thinking of buying the triton router to install onto my router table. it can be used as both a plunged router or a fixed base with a micro adjustment built into the handle but It also has a crank that can be threaded through my router table top. the only problem is that I have this table saw/router https://www.grizzly.com/products/10-5-HP-240V-Cabinet-Left-Tilting-Table-Saw/G1023RLWX it has no plate or space for a lift that's why im buying a router with a built in lift (also it saves me money so what ill have to do is drill a hole in my table saw top to fit in the crank. before I spend the money for the router is this a terrible idea to drill into table top? or will it be ok? also need to drill a hole for a pivot pin the table saw does not plan for that. https://www.youtube.com/watch?v=LF5Bs_lfC4k http://www.amazon.com/Triton-TRA001-Precision-Plunge-Router/dp/B00779ND0Q Quote
wdwerker Posted March 12, 2016 Report Posted March 12, 2016 Long before router table plates were available I made my own. Acrylic and aluminum can be worked with woodworking tools. Bolting a router under a fixed surface is a pain and makes it harder to fiddle with which eventually needs to be done. i made a plate big enough so the router could drop through the hole with a generous lip to support the plate. Gravity holds the router in place but you can add screws if needed. Pieces of playing cards are great for shimming the plate up to be perfectly flush with the table surface. Quote
duckkisser Posted March 12, 2016 Author Report Posted March 12, 2016 cant add a plate its already has a router space and the rest is solid metal just no router plate and im sick of squatting down to adjust my router that's why I want a crank. Quote
wdwerker Posted March 12, 2016 Report Posted March 12, 2016 I couldn't tell from the picture that the top was cast iron. Drilling if done carefully is not a problem. You do want to slightly chamfer both sides of the hole to prevent cracks from starting from a rough edge. Make damn sure there is room for the base of the router plus space for the crank without running into a rib under the top. Drilling through or trying to remove a rib is asking for trouble. I would make a template and make sure the crank, screw holes etc line up well before you mark and drill the metal. I would drill a much smaller pilot hole and work my way up to the full size. Using a drill press would be very smart. If a hand held drill catches it will try to break your wrist. Sharp bits are a must. Oil to lubricate and cool the bit is also smart. Quote
Cliff Posted March 13, 2016 Report Posted March 13, 2016 I have that router in my table and like it. Onliy had it a few months though. Quote
Just Bob Posted March 13, 2016 Report Posted March 13, 2016 Your reasons are exactly why I put the smaller Triton (2 1/2 hp) in my table saw extension. It is also cast and no way to add a plate. When I built my new shop I took the extension off and used it as a router table. The Triton is still in it. I really like the router with the above table bit change and height adjustment are great, and the dust collection rivals my OF1400. My only regret is that I did not buy the 3 1/2 hp model. It was out of stock at the time. Should have waited. Quote
duckkisser Posted March 14, 2016 Author Report Posted March 14, 2016 I just wrote to the company asking if the had a diagram showing where the adjustment is so I can figure out if the hole will go through a rib or not Quote
Robby W Posted March 14, 2016 Report Posted March 14, 2016 Take a look at the big Milwaukee 5625-20 router. It can also be adjusted from above the table. I have it in my table, with a lift, and it is the best router I have ever owned. Very good speed control, great chucks, brutal powerful. Quote
krtwood Posted March 14, 2016 Report Posted March 14, 2016 I've had the 2-1/4 triton router in my router table for about 8 years and while I did originally drill the hole for the above table adjustment thingy after the first couple times I stopped using it. It's easier to just reach under and turn the fine adjustment knob by hand than to get out the handle thing and get it to engage and make the adjustment. I moved to a different table and didn't bother drilling the hole for it. You gotta reach under there anyway to lock it. Well, you don't have to lock it but I do. While I can say lots of positive things about the 2-1/4, I can't say the same about the 3-1/4. It uses the same mechanism and it's too much weight for it so the movement up/down is really jerky. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.