kdj Posted October 4, 2016 Report Posted October 4, 2016 Hi Folks: This is my first post. I'm happy to be here. I made the dumb mistake of laying some green wood down on my NEW Saw Stop table saw and then had to go out of town for two weeks. When I returned I was horrified to see rust had formed on the table under the wood. What is the best way to remove and polish the table? Thanks in advance for any advice you all can offer. Quote
drzaius Posted October 4, 2016 Report Posted October 4, 2016 Welcome to the forums & sorry for your unhappy situation. It won't be the last time probably. Use a razor scraper to get off what you can & then move to a maroon Scotchbrite pad. If the rust has gone deeper, you may have to resort to coarse media like sand paper. The maroon pads seem to leave scratch pattern similar to the factory pattern. Quote
Barron Posted October 4, 2016 Report Posted October 4, 2016 Depending on how bad it is, I have removed rust spots with 0000 steel wool dipped in paste wax. I'll have to try the maroon pads, since I can't seem to avoid sweat drops working in an uncooled garage in a northern Virginia summer. Quote
Dknapp34 Posted October 4, 2016 Report Posted October 4, 2016 Just had this same issue with my sawstop when I forgot to clean off pressure treated saw dust. I just used some 600 grit sandpaper and followed it up with a fresh coat of paste wax. Sent from my iPad using Tapatalk Quote
shaneymack Posted October 4, 2016 Report Posted October 4, 2016 This is what I use to remove any rust spots. http://www.leevalley.com/en/wood/page.aspx?p=10509&cat=1,230,64343,64350 Then a coat of boeshield t9. Let that sit for a few minutes. Wipe of excess and then one coat of paste wax. Sent from my SM-N910W8 using Tapatalk Quote
kdj Posted October 5, 2016 Author Report Posted October 5, 2016 Hi Folks, Thanks so much for the quick replies. I did use the Scotch pads (burgundy) and paste when I first discovered the problem but I can still feel a bit of the rust with my fingertips. I'll try the razor to see if I can get it back to smooth. Quote
shaneymack Posted October 5, 2016 Report Posted October 5, 2016 Hi Folks, Thanks so much for the quick replies. I did use the Scotch pads (burgundy) and paste when I first discovered the problem but I can still feel a bit of the rust with my fingertips. I'll try the razor to see if I can get it back to smooth. Try using your scotchbrite pads this way: Sent from my SM-N910W8 using Tapatalk Quote
kdj Posted October 5, 2016 Author Report Posted October 5, 2016 Now THAT looks like a great solution. Perfect. Thanks. Quote
RichardA Posted October 5, 2016 Report Posted October 5, 2016 13 minutes ago, shaneymack said: Try using your scotchbrite pads this way: That's how I do it with #0000 steel wool and WD40. Sent from my SM-N910W8 using Tapatalk Quote
TerryMcK Posted October 5, 2016 Report Posted October 5, 2016 I use fine grit sandpaper or scotchbrite pad. T9 over the top and then some pastewax. Not too bothered if I can't see my reflection in it. One thing I do do though is leave a sheet of hardboard on it after use. Then if I use the table saw as a table (who doesn't) it is protected. Quote
estesbubba Posted October 5, 2016 Report Posted October 5, 2016 Start with step 4 and use CRC 3-36 instead of wax. http://woodworkerszone.com/wiki/index.php?title=Daves_dirty_dozen Quote
Popular Post Eric. Posted October 5, 2016 Popular Post Report Posted October 5, 2016 After you get your table cleaned, be sure not to cut into that green wood with your SawStop or you're gonna have more reasons to hate yourself. 3 Quote
AceHoleInOne Posted October 5, 2016 Report Posted October 5, 2016 Spray the rust areas with wd40 then sand with 600 grit wet/dry sand paper. I thought Sawstop was the be-all, catch-all....they rust -Ace- Quote
AstroDave Posted October 5, 2016 Report Posted October 5, 2016 When Festool makes a table saw it will be rust free...however you may have a slight green patina Sent from my SM-G930V using Tapatalk Quote
Eric. Posted October 5, 2016 Report Posted October 5, 2016 5 minutes ago, SplinteredDave said: When Festool makes a table saw it will be rust free...however you may have a slight green patina And a second mortgage. 2 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.