Popular Post estesbubba Posted October 29, 2016 Popular Post Report Posted October 29, 2016 ...better than I thought it would. Not 100% collection but about as good as table saw and probably better than bandsaw. Once I seal up top board pipe goes through it should be better. One cut with dust collection on. One cut without. Pretty simple setup. 3 Quote
Keggers Posted October 29, 2016 Report Posted October 29, 2016 Maybe you could attach a board to the left (under the collector pipe) at an angle? That might keep the dust closer to your pipe opening and improve on dust collection. I have a shop vac attached to my miter saw. I've just added a dust deputy in hopes of keeping the vac and filter from filling up thus improving the collection performance. So far I'm happy with it. Quote
bushwacked Posted October 29, 2016 Report Posted October 29, 2016 Great idea! What happens though if you cut a left 45? 1 Quote
Keggers Posted October 29, 2016 Report Posted October 29, 2016 2 hours ago, bushwacked said: Great idea! What happens though if you cut a left 45? I hadn't really thought about that. I just use my miter saw to break down longer boards and cut my miters on my table saw. I guess my idea wouldn't be practical. Quote
Chet Posted October 30, 2016 Report Posted October 30, 2016 The Bosch Glide saws have a dust exhaust port that swivels so he can always keep it pointed in the direction of the dust collector. Quote
ben_r_ Posted October 30, 2016 Report Posted October 30, 2016 I would add something like this to that drop: LINK Quote
Ronn W Posted October 30, 2016 Report Posted October 30, 2016 Seems like the closer you can get the end of the duct to the dust source, the better. Air is moving fastest at the opening to the duct. Quote
estesbubba Posted October 30, 2016 Author Report Posted October 30, 2016 Did a test using my Festool CT and it was slightly better than the cyclone but still left some dust. Might try and improve the cyclone but happy how my first attempt works. I'm glad the cyclone will do good enough because it's a lot more convenient than moving the CT around. Quote
ben_r_ Posted October 30, 2016 Report Posted October 30, 2016 12 hours ago, estesbubba said: Did a test using my Festool CT and it was slightly better than the cyclone but still left some dust. Might try and improve the cyclone but happy how my first attempt works. I'm glad the cyclone will do good enough because it's a lot more convenient than moving the CT around. When you tested with the CT did you just plug the hose directly into the dust outlet from the saw? If so thatll collect the larger particles but the fines that dont get thrown into the outlet dust port will remain floating around for you to breathe. That is where the higher air volume moving properties of a real dust collector are of benefit as they move more air volume to collect the finer particles. Id concentrate more on enclosing and air sealing as much as you can around the miter saw and using the dust collector to collect the dust. Quote
estesbubba Posted October 31, 2016 Author Report Posted October 31, 2016 I added a rubber chute and it does great but some dust goes under and around the port on the saw. This happens even with the CT and a complaint people have with the Bosch Glide vs the Kapex. It's not bad and some people have modified the shroud so I'll try that sometime. Quote
Brendon_t Posted October 31, 2016 Report Posted October 31, 2016 I would call that a winner. especially since there really isn't a great way to extract from the mitre saw. it seems more like a game of "let's try to make it suck less" Quote
wdwerker Posted October 31, 2016 Report Posted October 31, 2016 Sloped area behind and downdraft dust collection is how I'm going. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.